From: Linus Lüssing <ll@simonwunderlich.de> stable inclusion from stable-5.10.80 commit d01e847d84bf698206febd59a169b60eb2b3e077 bugzilla: 185821 https://gitee.com/openeuler/kernel/issues/I4L7CG Reference: https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?id=... -------------------------------- [ Upstream commit 4925642d541278575ad1948c5924d71ffd57ef14 ] In tests with two Lima boards from 8devices (QCA4531 based) on OpenWrt 19.07 we could force a silent restart of a device with no serial output when we were sending a high amount of UDP traffic (iperf3 at 80 MBit/s in both directions from external hosts, saturating the wifi and causing a load of about 4.5 to 6) and were then triggering an ath9k_queue_reset(). Further debugging showed that the restart was caused by the ath79 watchdog. With disabled watchdog we could observe that the device was constantly going into ath_isr() interrupt handler and was returning early after the ATH_OP_HW_RESET flag test, without clearing any interrupts. Even though ath9k_queue_reset() calls ath9k_hw_kill_interrupts(). With JTAG we could observe the following race condition: 1) ath9k_queue_reset() ... -> ath9k_hw_kill_interrupts() -> set_bit(ATH_OP_HW_RESET, &common->op_flags); ... <- returns 2) ath9k_tasklet() ... -> ath9k_hw_resume_interrupts() ... <- returns 3) loops around: ... handle_int() -> ath_isr() ... -> if (test_bit(ATH_OP_HW_RESET, &common->op_flags)) return IRQ_HANDLED; x) ath_reset_internal(): => never reached <= And in ath_isr() we would typically see the following interrupts / interrupt causes: * status: 0x00111030 or 0x00110030 * async_cause: 2 (AR_INTR_MAC_IPQ) * sync_cause: 0 So the ath9k_tasklet() reenables the ath9k interrupts through ath9k_hw_resume_interrupts() which ath9k_queue_reset() had just disabled. And ath_isr() then keeps firing because it returns IRQ_HANDLED without actually clearing the interrupt. To fix this IRQ storm also clear/disable the interrupts again when we are in reset state. Cc: Sven Eckelmann <sven@narfation.org> Cc: Simon Wunderlich <sw@simonwunderlich.de> Cc: Linus Lüssing <linus.luessing@c0d3.blue> Fixes: 872b5d814f99 ("ath9k: do not access hardware on IRQs during reset") Signed-off-by: Linus Lüssing <ll@simonwunderlich.de> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20210914192515.9273-3-linus.luessing@c0d3.blue Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Chen Jun <chenjun102@huawei.com> Reviewed-by: Weilong Chen <chenweilong@huawei.com> Acked-by: Weilong Chen <chenweilong@huawei.com> Signed-off-by: Chen Jun <chenjun102@huawei.com> Signed-off-by: Zheng Zengkai <zhengzengkai@huawei.com> --- drivers/net/wireless/ath/ath9k/main.c | 4 +++- 1 file changed, 3 insertions(+), 1 deletion(-) diff --git a/drivers/net/wireless/ath/ath9k/main.c b/drivers/net/wireless/ath/ath9k/main.c index 5739c1dbf166..af367696fd92 100644 --- a/drivers/net/wireless/ath/ath9k/main.c +++ b/drivers/net/wireless/ath/ath9k/main.c @@ -533,8 +533,10 @@ irqreturn_t ath_isr(int irq, void *dev) ath9k_debug_sync_cause(sc, sync_cause); status &= ah->imask; /* discard unasked-for bits */ - if (test_bit(ATH_OP_HW_RESET, &common->op_flags)) + if (test_bit(ATH_OP_HW_RESET, &common->op_flags)) { + ath9k_hw_kill_interrupts(sc->sc_ah); return IRQ_HANDLED; + } /* * If there are no status bits set, then this interrupt was not -- 2.20.1