From: Hans de Goede hdegoede@redhat.com
stable inclusion from linux-4.19.207 commit 91264ae7fceb7e30172ab7dd27e3e41751cb83b3
--------------------------------
[ Upstream commit f949a9ebce7a18005266b859a17f10c891bb13d7 ]
On Cherry Trail devices with an AXP288 PMIC the external SD-card slot used the AXP's DLDO2 as card-voltage and either DLDO3 or GPIO1LDO (GPIO1 pin in low noise LDO mode) as signal-voltage.
These regulators are turned on/off and in case of the signal-voltage also have their output-voltage changed by the _PS0 and _PS3 power- management ACPI methods on the MMC-controllers ACPI fwnode as well as by the _DSM ACPI method for changing the signal voltage.
The AML code implementing these methods is directly accessing the PMIC through ACPI I2C OpRegion accesses, instead of using the special PMIC OpRegion handled by drivers/acpi/pmic/intel_pmic_xpower.c .
This means that the contents of the involved PMIC registers can change without the change being made through the regmap interface, so regmap should not cache the contents of these registers.
Mark the regulator power on/off, the regulator voltage control and the GPIO1 control registers as volatile, to avoid regmap caching them.
Specifically this fixes an issue on some models where the i915 driver toggles another LDO using the same on/off register on/off through MIPI sequences (through intel_soc_pmic_exec_mipi_pmic_seq_element()) which then writes back a cached on/off register-value where the card-voltage is off causing the external sdcard slot to stop working when the screen goes blank, or comes back on again.
The regulator register-range now marked volatile also includes the buck regulator control registers. This is done on purpose these are normally not touched by the AML code, but they are updated directly by the SoC's PUNIT which means that they may also change without going through regmap.
Note the AXP288 PMIC is only used on Bay- and Cherry-Trail platforms, so even though this is an ACPI specific problem there is no need to make the new volatile ranges conditional since these platforms always use ACPI.
Fixes: dc91c3b6fe66 ("mfd: axp20x: Mark AXP20X_VBUS_IPSOUT_MGMT as volatile") Fixes: cd53216625a0 ("mfd: axp20x: Fix axp288 volatile ranges") Reported-and-tested-by: Clamshell clamfly@163.com Signed-off-by: Hans de Goede hdegoede@redhat.com Reviewed-by: Chen-Yu Tsai wens@csie.org Signed-off-by: Lee Jones lee.jones@linaro.org Signed-off-by: Sasha Levin sashal@kernel.org Signed-off-by: Yang Yingliang yangyingliang@huawei.com --- drivers/mfd/axp20x.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-)
diff --git a/drivers/mfd/axp20x.c b/drivers/mfd/axp20x.c index aa65931142ba7..dcb341d627582 100644 --- a/drivers/mfd/axp20x.c +++ b/drivers/mfd/axp20x.c @@ -127,12 +127,13 @@ static const struct regmap_range axp288_writeable_ranges[] = {
static const struct regmap_range axp288_volatile_ranges[] = { regmap_reg_range(AXP20X_PWR_INPUT_STATUS, AXP288_POWER_REASON), + regmap_reg_range(AXP22X_PWR_OUT_CTRL1, AXP22X_ALDO3_V_OUT), regmap_reg_range(AXP288_BC_GLOBAL, AXP288_BC_GLOBAL), regmap_reg_range(AXP288_BC_DET_STAT, AXP20X_VBUS_IPSOUT_MGMT), regmap_reg_range(AXP20X_CHRG_BAK_CTRL, AXP20X_CHRG_BAK_CTRL), regmap_reg_range(AXP20X_IRQ1_EN, AXP20X_IPSOUT_V_HIGH_L), regmap_reg_range(AXP20X_TIMER_CTRL, AXP20X_TIMER_CTRL), - regmap_reg_range(AXP22X_GPIO_STATE, AXP22X_GPIO_STATE), + regmap_reg_range(AXP20X_GPIO1_CTRL, AXP22X_GPIO_STATE), regmap_reg_range(AXP288_RT_BATT_V_H, AXP288_RT_BATT_V_L), regmap_reg_range(AXP20X_FG_RES, AXP288_FG_CC_CAP_REG), };