From: Sasi Kumar sasi.kumar@broadcom.com
[ Upstream commit a95bdfd22076497288868c028619bc5995f5cc7f ]
Multiple connects/disconnects can cause a crash on the second disconnect. The driver had a problem where it would try to send endpoint commands after it was disconnected which is not allowed by the hardware. The fix is to only allow the endpoint commands when the endpoint is connected. This will also fix issues that showed up when using configfs to create gadgets.
Signed-off-by: Sasi Kumar sasi.kumar@broadcom.com Signed-off-by: Al Cooper alcooperx@gmail.com Acked-by: Florian Fainelli f.fainelli@gmail.com Signed-off-by: Felipe Balbi balbi@kernel.org Signed-off-by: Sasha Levin sashal@kernel.org Signed-off-by: Yang Yingliang yangyingliang@huawei.com --- drivers/usb/gadget/udc/bdc/bdc_core.c | 4 ++++ drivers/usb/gadget/udc/bdc/bdc_ep.c | 16 ++++++++++------ 2 files changed, 14 insertions(+), 6 deletions(-)
diff --git a/drivers/usb/gadget/udc/bdc/bdc_core.c b/drivers/usb/gadget/udc/bdc/bdc_core.c index 01b44e1596237..4c557f3154460 100644 --- a/drivers/usb/gadget/udc/bdc/bdc_core.c +++ b/drivers/usb/gadget/udc/bdc/bdc_core.c @@ -283,6 +283,7 @@ static void bdc_mem_init(struct bdc *bdc, bool reinit) * in that case reinit is passed as 1 */ if (reinit) { + int i; /* Enable interrupts */ temp = bdc_readl(bdc->regs, BDC_BDCSC); temp |= BDC_GIE; @@ -292,6 +293,9 @@ static void bdc_mem_init(struct bdc *bdc, bool reinit) /* Initialize SRR to 0 */ memset(bdc->srr.sr_bds, 0, NUM_SR_ENTRIES * sizeof(struct bdc_bd)); + /* clear ep flags to avoid post disconnect stops/deconfigs */ + for (i = 1; i < bdc->num_eps; ++i) + bdc->bdc_ep_array[i]->flags = 0; } else { /* One time initiaization only */ /* Enable status report function pointers */ diff --git a/drivers/usb/gadget/udc/bdc/bdc_ep.c b/drivers/usb/gadget/udc/bdc/bdc_ep.c index d49c6dc1082dc..9ddc0b4e92c9c 100644 --- a/drivers/usb/gadget/udc/bdc/bdc_ep.c +++ b/drivers/usb/gadget/udc/bdc/bdc_ep.c @@ -615,7 +615,6 @@ int bdc_ep_enable(struct bdc_ep *ep) } bdc_dbg_bd_list(bdc, ep); /* only for ep0: config ep is called for ep0 from connect event */ - ep->flags |= BDC_EP_ENABLED; if (ep->ep_num == 1) return ret;
@@ -759,10 +758,13 @@ static int ep_dequeue(struct bdc_ep *ep, struct bdc_req *req) __func__, ep->name, start_bdi, end_bdi); dev_dbg(bdc->dev, "ep_dequeue ep=%p ep->desc=%p\n", ep, (void *)ep->usb_ep.desc); - /* Stop the ep to see where the HW is ? */ - ret = bdc_stop_ep(bdc, ep->ep_num); - /* if there is an issue with stopping ep, then no need to go further */ - if (ret) + /* if still connected, stop the ep to see where the HW is ? */ + if (!(bdc_readl(bdc->regs, BDC_USPC) & BDC_PST_MASK)) { + ret = bdc_stop_ep(bdc, ep->ep_num); + /* if there is an issue, then no need to go further */ + if (ret) + return 0; + } else return 0;
/* @@ -1911,7 +1913,9 @@ static int bdc_gadget_ep_disable(struct usb_ep *_ep) __func__, ep->name, ep->flags);
if (!(ep->flags & BDC_EP_ENABLED)) { - dev_warn(bdc->dev, "%s is already disabled\n", ep->name); + if (bdc->gadget.speed != USB_SPEED_UNKNOWN) + dev_warn(bdc->dev, "%s is already disabled\n", + ep->name); return 0; } spin_lock_irqsave(&bdc->lock, flags);