From: Yanteng Si siyanteng@loongson.cn
maillist inclusion category: feature bugzilla: https://gitee.com/openeuler/kernel/issues/I9RPAR
Reference: https://lore.kernel.org/all/cover.1714046812.git.siyanteng@loongson.cn
--------------------------------
There are two types of Loongson DWGMAC. The first type shares the same register definitions and has similar logic as dwmac1000. The second type uses several different register definitions, we think it is necessary to distinguish rx and tx, so we split these bits into two.
Simply put, we split some single bit fields into double bits fileds:
Name Tx Rx
DMA_INTR_ENA_NIE = 0x00040000 | 0x00020000; DMA_INTR_ENA_AIE = 0x00010000 | 0x00008000; DMA_STATUS_NIS = 0x00040000 | 0x00020000; DMA_STATUS_AIS = 0x00010000 | 0x00008000; DMA_STATUS_FBI = 0x00002000 | 0x00001000;
Therefore, when using, TX and RX must be set at the same time.
How to use them: 1. Create the Loongson GNET-specific stmmac_dma_ops.dma_interrupt() stmmac_dma_ops.init_chan() methods in the dwmac-loongson.c driver. Adding all the Loongson-specific macros
2. Create a Loongson GNET-specific platform setup method with the next semantics: + allocate stmmac_dma_ops instance and initialize it with dwmac1000_dma_ops. + override the stmmac_dma_ops.{dma_interrupt, init_chan} with the pointers to the methods defined in 2. + allocate mac_device_info instance and initialize the mac_device_info.dma field with a pointer to the new stmmac_dma_ops instance. + initialize mac_device_info in a way it's done in dwmac1000_setup().
3. Initialize plat_stmmacenet_data.setup() with the pointer to the method created in 2.
GNET features:
Speeds: 10/100/1000Mbps DMA-descriptors type: enhanced L3/L4 filters availability: support VLAN hash table filter: support PHY-interface: GMII Remote Wake-up support: support Mac Management Counters (MMC): support Number of additional MAC addresses: 5 MAC Hash-based filter: support Number of ash table size: 256 DMA chennel number: 0x10 device is 8 and 0x37 device is 1
Others:
GNET integrates both MAC and PHY chips inside. GNET device: LS2K2000, LS7A2000, the chip connection between the mac and phy of these devices is not normal and requires two rounds of negotiation; LS7A2000 does not support half-duplex and multi-channel;
To enable multi-channel on LS2K2000, you need to turn off hardware checksum.
**Note**: Currently, only the LS2K2000's synopsys_id is 0x10, while the synopsys_id of other devices are 0x37.
Signed-off-by: Feiyang Chen chenfeiyang@loongson.cn Signed-off-by: Yinggang Gu guyinggang@loongson.cn Signed-off-by: Yanteng Si siyanteng@loongson.cn Signed-off-by: Ming Wang wangming01@loongson.cn --- drivers/net/ethernet/stmicro/stmmac/common.h | 1 + .../ethernet/stmicro/stmmac/dwmac-loongson.c | 381 +++++++++++++++++- 2 files changed, 371 insertions(+), 11 deletions(-)
diff --git a/drivers/net/ethernet/stmicro/stmmac/common.h b/drivers/net/ethernet/stmicro/stmmac/common.h index 4dbc076f72d6..f9a3f3321e59 100644 --- a/drivers/net/ethernet/stmicro/stmmac/common.h +++ b/drivers/net/ethernet/stmicro/stmmac/common.h @@ -29,6 +29,7 @@ /* Synopsys Core versions */ #define DWMAC_CORE_3_40 0x34 #define DWMAC_CORE_3_50 0x35 +#define DWMAC_CORE_3_70 0x37 #define DWMAC_CORE_4_00 0x40 #define DWMAC_CORE_4_10 0x41 #define DWMAC_CORE_5_00 0x50 diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c b/drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c index a16bba389417..68de90c44feb 100644 --- a/drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c +++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c @@ -8,9 +8,71 @@ #include <linux/device.h> #include <linux/of_irq.h> #include "stmmac.h" +#include "dwmac_dma.h" +#include "dwmac1000.h" + +/* Normal Loongson Tx Summary */ +#define DMA_INTR_ENA_NIE_TX_LOONGSON 0x00040000 +/* Normal Loongson Rx Summary */ +#define DMA_INTR_ENA_NIE_RX_LOONGSON 0x00020000 + +#define DMA_INTR_NORMAL_LOONGSON (DMA_INTR_ENA_NIE_TX_LOONGSON | \ + DMA_INTR_ENA_NIE_RX_LOONGSON | \ + DMA_INTR_ENA_RIE | DMA_INTR_ENA_TIE) + +/* Abnormal Loongson Tx Summary */ +#define DMA_INTR_ENA_AIE_TX_LOONGSON 0x00010000 +/* Abnormal Loongson Rx Summary */ +#define DMA_INTR_ENA_AIE_RX_LOONGSON 0x00008000 + +#define DMA_INTR_ABNORMAL_LOONGSON (DMA_INTR_ENA_AIE_TX_LOONGSON | \ + DMA_INTR_ENA_AIE_RX_LOONGSON | \ + DMA_INTR_ENA_FBE | DMA_INTR_ENA_UNE) + +#define DMA_INTR_DEFAULT_MASK_LOONGSON (DMA_INTR_NORMAL_LOONGSON | \ + DMA_INTR_ABNORMAL_LOONGSON) + +/* Normal Loongson Tx Interrupt Summary */ +#define DMA_STATUS_NIS_TX_LOONGSON 0x00040000 +/* Normal Loongson Rx Interrupt Summary */ +#define DMA_STATUS_NIS_RX_LOONGSON 0x00020000 + +/* Abnormal Loongson Tx Interrupt Summary */ +#define DMA_STATUS_AIS_TX_LOONGSON 0x00010000 +/* Abnormal Loongson Rx Interrupt Summary */ +#define DMA_STATUS_AIS_RX_LOONGSON 0x00008000 + +/* Fatal Loongson Tx Bus Error Interrupt */ +#define DMA_STATUS_FBI_TX_LOONGSON 0x00002000 +/* Fatal Loongson Rx Bus Error Interrupt */ +#define DMA_STATUS_FBI_RX_LOONGSON 0x00001000 + +#define DMA_STATUS_MSK_COMMON_LOONGSON (DMA_STATUS_NIS_TX_LOONGSON | \ + DMA_STATUS_NIS_RX_LOONGSON | \ + DMA_STATUS_AIS_TX_LOONGSON | \ + DMA_STATUS_AIS_RX_LOONGSON | \ + DMA_STATUS_FBI_TX_LOONGSON | \ + DMA_STATUS_FBI_RX_LOONGSON) + +#define DMA_STATUS_MSK_RX_LOONGSON (DMA_STATUS_ERI | DMA_STATUS_RWT | \ + DMA_STATUS_RPS | DMA_STATUS_RU | \ + DMA_STATUS_RI | DMA_STATUS_OVF | \ + DMA_STATUS_MSK_COMMON_LOONGSON) + +#define DMA_STATUS_MSK_TX_LOONGSON (DMA_STATUS_ETI | DMA_STATUS_UNF | \ + DMA_STATUS_TJT | DMA_STATUS_TU | \ + DMA_STATUS_TPS | DMA_STATUS_TI | \ + DMA_STATUS_MSK_COMMON_LOONGSON)
#define PCI_DEVICE_ID_LOONGSON_GMAC 0x7a03 #define PCI_DEVICE_ID_LOONGSON_GNET 0x7a13 +#define LOONGSON_DWMAC_CORE_1_00 0x10 /* Loongson custom IP */ +#define CHANNEL_NUM 8 + +struct loongson_data { + u32 gmac_verion; + struct device *dev; +};
struct stmmac_pci_info { int (*setup)(struct pci_dev *pdev, struct plat_stmmacenet_data *plat); @@ -69,6 +131,168 @@ static struct stmmac_pci_info loongson_gmac_pci_info = { .setup = loongson_gmac_data, };
+static void loongson_gnet_dma_init_channel(struct stmmac_priv *priv, + void __iomem *ioaddr, + struct stmmac_dma_cfg *dma_cfg, + u32 chan) +{ + int txpbl = dma_cfg->txpbl ?: dma_cfg->pbl; + int rxpbl = dma_cfg->rxpbl ?: dma_cfg->pbl; + u32 value; + + value = readl(ioaddr + DMA_CHAN_BUS_MODE(chan)); + + if (dma_cfg->pblx8) + value |= DMA_BUS_MODE_MAXPBL; + + value |= DMA_BUS_MODE_USP; + value &= ~(DMA_BUS_MODE_PBL_MASK | DMA_BUS_MODE_RPBL_MASK); + value |= (txpbl << DMA_BUS_MODE_PBL_SHIFT); + value |= (rxpbl << DMA_BUS_MODE_RPBL_SHIFT); + + /* Set the Fixed burst mode */ + if (dma_cfg->fixed_burst) + value |= DMA_BUS_MODE_FB; + + /* Mixed Burst has no effect when fb is set */ + if (dma_cfg->mixed_burst) + value |= DMA_BUS_MODE_MB; + + if (dma_cfg->atds) + value |= DMA_BUS_MODE_ATDS; + + if (dma_cfg->aal) + value |= DMA_BUS_MODE_AAL; + + writel(value, ioaddr + DMA_CHAN_BUS_MODE(chan)); + + /* Mask interrupts by writing to CSR7 */ + writel(DMA_INTR_DEFAULT_MASK_LOONGSON, ioaddr + + DMA_CHAN_INTR_ENA(chan)); +} + +static int loongson_gnet_dma_interrupt(struct stmmac_priv *priv, + void __iomem *ioaddr, + struct stmmac_extra_stats *x, + u32 chan, u32 dir) +{ + struct stmmac_pcpu_stats *stats = this_cpu_ptr(priv->xstats.pcpu_stats); + u32 abnor_intr_status; + u32 nor_intr_status; + u32 fb_intr_status; + u32 intr_status; + int ret = 0; + + /* read the status register (CSR5) */ + intr_status = readl(ioaddr + DMA_CHAN_STATUS(chan)); + + if (dir == DMA_DIR_RX) + intr_status &= DMA_STATUS_MSK_RX_LOONGSON; + else if (dir == DMA_DIR_TX) + intr_status &= DMA_STATUS_MSK_TX_LOONGSON; + + nor_intr_status = intr_status & (DMA_STATUS_NIS_TX_LOONGSON | + DMA_STATUS_NIS_RX_LOONGSON); + abnor_intr_status = intr_status & (DMA_STATUS_AIS_TX_LOONGSON | + DMA_STATUS_AIS_RX_LOONGSON); + fb_intr_status = intr_status & (DMA_STATUS_FBI_TX_LOONGSON | + DMA_STATUS_FBI_RX_LOONGSON); + + /* ABNORMAL interrupts */ + if (unlikely(abnor_intr_status)) { + if (unlikely(intr_status & DMA_STATUS_UNF)) { + ret = tx_hard_error_bump_tc; + x->tx_undeflow_irq++; + } + if (unlikely(intr_status & DMA_STATUS_TJT)) + x->tx_jabber_irq++; + if (unlikely(intr_status & DMA_STATUS_OVF)) + x->rx_overflow_irq++; + if (unlikely(intr_status & DMA_STATUS_RU)) + x->rx_buf_unav_irq++; + if (unlikely(intr_status & DMA_STATUS_RPS)) + x->rx_process_stopped_irq++; + if (unlikely(intr_status & DMA_STATUS_RWT)) + x->rx_watchdog_irq++; + if (unlikely(intr_status & DMA_STATUS_ETI)) + x->tx_early_irq++; + if (unlikely(intr_status & DMA_STATUS_TPS)) { + x->tx_process_stopped_irq++; + ret = tx_hard_error; + } + if (unlikely(fb_intr_status)) { + x->fatal_bus_error_irq++; + ret = tx_hard_error; + } + } + /* TX/RX NORMAL interrupts */ + if (likely(nor_intr_status)) { + if (likely(intr_status & DMA_STATUS_RI)) { + u32 value = readl(ioaddr + DMA_INTR_ENA); + /* to schedule NAPI on real RIE event. */ + if (likely(value & DMA_INTR_ENA_RIE)) { + u64_stats_update_begin(&stats->syncp); + u64_stats_inc(&stats->rx_normal_irq_n[chan]); + u64_stats_update_end(&stats->syncp); + ret |= handle_rx; + } + } + if (likely(intr_status & DMA_STATUS_TI)) { + u64_stats_update_begin(&stats->syncp); + u64_stats_inc(&stats->tx_normal_irq_n[chan]); + u64_stats_update_end(&stats->syncp); + ret |= handle_tx; + } + if (unlikely(intr_status & DMA_STATUS_ERI)) + x->rx_early_irq++; + } + /* Optional hardware blocks, interrupts should be disabled */ + if (unlikely(intr_status & + (DMA_STATUS_GPI | DMA_STATUS_GMI | DMA_STATUS_GLI))) + pr_warn("%s: unexpected status %08x\n", __func__, intr_status); + + /* Clear the interrupt by writing a logic 1 to the CSR5[15-0] */ + writel((intr_status & 0x7ffff), ioaddr + DMA_CHAN_STATUS(chan)); + + return ret; +} + +static void loongson_gnet_fix_speed(void *priv, unsigned int speed, + unsigned int mode) +{ + struct loongson_data *ld = (struct loongson_data *)priv; + struct net_device *ndev = dev_get_drvdata(ld->dev); + struct stmmac_priv *ptr = netdev_priv(ndev); + + /* The controller and PHY don't work well together. + * We need to use the PS bit to check if the controller's status + * is correct and reset PHY if necessary. + * MAC_CTRL_REG.15 is defined by the GMAC_CONTROL_PS macro. + */ + if (speed == SPEED_1000) { + if (readl(ptr->ioaddr + MAC_CTRL_REG) & + GMAC_CONTROL_PS) + /* Word around hardware bug, restart autoneg */ + phy_restart_aneg(ndev->phydev); + } +} + +static int loongson_gnet_data(struct pci_dev *pdev, + struct plat_stmmacenet_data *plat) +{ + loongson_default_data(pdev, plat); + + plat->phy_interface = PHY_INTERFACE_MODE_GMII; + plat->mdio_bus_data->phy_mask = ~(u32)BIT(2); + plat->fix_mac_speed = loongson_gnet_fix_speed; + + return 0; +} + +static struct stmmac_pci_info loongson_gnet_pci_info = { + .setup = loongson_gnet_data, +}; + static int loongson_dwmac_config_legacy(struct pci_dev *pdev, struct plat_stmmacenet_data *plat, struct stmmac_resources *res, @@ -101,12 +325,126 @@ static int loongson_dwmac_config_legacy(struct pci_dev *pdev, return 0; }
+static int loongson_dwmac_config_msi(struct pci_dev *pdev, + struct plat_stmmacenet_data *plat, + struct stmmac_resources *res, + struct device_node *np) +{ + int i, ret, vecs; + + vecs = roundup_pow_of_two(CHANNEL_NUM * 2 + 1); + ret = pci_alloc_irq_vectors(pdev, vecs, vecs, PCI_IRQ_MSI); + if (ret < 0) { + dev_info(&pdev->dev, + "MSI enable failed, Fallback to legacy interrupt\n"); + return loongson_dwmac_config_legacy(pdev, plat, res, np); + } + + res->irq = pci_irq_vector(pdev, 0); + res->wol_irq = 0; + + /* INT NAME | MAC | CH7 rx | CH7 tx | ... | CH0 rx | CH0 tx | + * --------- ----- -------- -------- ... -------- -------- + * IRQ NUM | 0 | 1 | 2 | ... | 15 | 16 | + */ + for (i = 0; i < CHANNEL_NUM; i++) { + res->rx_irq[CHANNEL_NUM - 1 - i] = + pci_irq_vector(pdev, 1 + i * 2); + res->tx_irq[CHANNEL_NUM - 1 - i] = + pci_irq_vector(pdev, 2 + i * 2); + } + + plat->flags |= STMMAC_FLAG_MULTI_MSI_EN; + + return 0; +} + +static struct mac_device_info *loongson_dwmac_setup(void *apriv) +{ + struct stmmac_priv *priv = apriv; + struct mac_device_info *mac; + struct stmmac_dma_ops *dma; + struct loongson_data *ld; + struct pci_dev *pdev; + + ld = priv->plat->bsp_priv; + pdev = to_pci_dev(priv->device); + + mac = devm_kzalloc(priv->device, sizeof(*mac), GFP_KERNEL); + if (!mac) + return NULL; + + dma = devm_kzalloc(priv->device, sizeof(*dma), GFP_KERNEL); + if (!dma) + return NULL; + + /* The original IP-core version is 0x37 in all Loongson GNET + * (ls2k2000 and ls7a2000), but the GNET HW designers have changed the + * GMAC_VERSION.SNPSVER field to the custom 0x10 value on the Loongson + * ls2k2000 MAC to emphasize the differences: multiple DMA-channels, + * AV feature and GMAC_INT_STATUS CSR flags layout. Get back the + * original value so the correct HW-interface would be selected. + */ + if (ld->gmac_verion == LOONGSON_DWMAC_CORE_1_00) { + priv->synopsys_id = DWMAC_CORE_3_70; + *dma = dwmac1000_dma_ops; + dma->init_chan = loongson_gnet_dma_init_channel; + dma->dma_interrupt = loongson_gnet_dma_interrupt; + mac->dma = dma; + } + + mac->mac = &dwmac1000_ops; + priv->dev->priv_flags |= IFF_UNICAST_FLT; + + /* Pre-initialize the respective "mac" fields as it's done in + * dwmac1000_setup() + */ + mac->pcsr = priv->ioaddr; + mac->multicast_filter_bins = priv->plat->multicast_filter_bins; + mac->unicast_filter_entries = priv->plat->unicast_filter_entries; + mac->mcast_bits_log2 = 0; + + if (mac->multicast_filter_bins) + mac->mcast_bits_log2 = ilog2(mac->multicast_filter_bins); + + /* The GMAC devices with PCI ID 0x7a03 does not support any pause mode. + * The GNET devices without CORE ID 0x10 does not support half-duplex. + */ + if (pdev->device == PCI_DEVICE_ID_LOONGSON_GMAC) { + mac->link.caps = MAC_10 | MAC_100 | MAC_1000; + } else { + if (ld->gmac_verion == LOONGSON_DWMAC_CORE_1_00) + mac->link.caps = MAC_ASYM_PAUSE | MAC_SYM_PAUSE | + MAC_10 | MAC_100 | MAC_1000; + else + mac->link.caps = MAC_ASYM_PAUSE | MAC_SYM_PAUSE | + MAC_10FD | MAC_100FD | MAC_1000FD; + } + + mac->link.duplex = GMAC_CONTROL_DM; + mac->link.speed10 = GMAC_CONTROL_PS; + mac->link.speed100 = GMAC_CONTROL_PS | GMAC_CONTROL_FES; + mac->link.speed1000 = 0; + mac->link.speed_mask = GMAC_CONTROL_PS | GMAC_CONTROL_FES; + mac->mii.addr = GMAC_MII_ADDR; + mac->mii.data = GMAC_MII_DATA; + mac->mii.addr_shift = 11; + mac->mii.addr_mask = 0x0000F800; + mac->mii.reg_shift = 6; + mac->mii.reg_mask = 0x000007C0; + mac->mii.clk_csr_shift = 2; + mac->mii.clk_csr_mask = GENMASK(5, 2); + + return mac; +} + static int loongson_dwmac_probe(struct pci_dev *pdev, const struct pci_device_id *id) { struct plat_stmmacenet_data *plat; int ret, i, bus_id, phy_mode; struct stmmac_pci_info *info; struct stmmac_resources res; + struct loongson_data *ld; struct device_node *np;
np = dev_of_node(&pdev->dev); @@ -122,10 +460,12 @@ static int loongson_dwmac_probe(struct pci_dev *pdev, const struct pci_device_id return -ENOMEM;
plat->dma_cfg = devm_kzalloc(&pdev->dev, sizeof(*plat->dma_cfg), GFP_KERNEL); - if (!plat->dma_cfg) { - ret = -ENOMEM; - goto err_put_node; - } + if (!plat->dma_cfg) + return -ENOMEM; + + ld = devm_kzalloc(&pdev->dev, sizeof(*ld), GFP_KERNEL); + if (!ld) + return -ENOMEM;
/* Enable pci device */ ret = pci_enable_device(pdev); @@ -171,14 +511,34 @@ static int loongson_dwmac_probe(struct pci_dev *pdev, const struct pci_device_id plat->phy_interface = phy_mode; }
- pci_enable_msi(pdev); + plat->bsp_priv = ld; + plat->setup = loongson_dwmac_setup; + ld->dev = &pdev->dev; + memset(&res, 0, sizeof(res)); res.addr = pcim_iomap_table(pdev)[0]; + ld->gmac_verion = readl(res.addr + GMAC_VERSION) & 0xff; + + switch (ld->gmac_verion) { + case LOONGSON_DWMAC_CORE_1_00: + plat->rx_queues_to_use = CHANNEL_NUM; + plat->tx_queues_to_use = CHANNEL_NUM; + + /* Only channel 0 supports checksum, + * so turn off checksum to enable multiple channels. + */ + for (i = 1; i < CHANNEL_NUM; i++) + plat->tx_queues_cfg[i].coe_unsupported = 1;
- plat->tx_queues_to_use = 1; - plat->rx_queues_to_use = 1; + ret = loongson_dwmac_config_msi(pdev, plat, &res, np); + break; + default: /* 0x35 device and 0x37 device. */ + plat->tx_queues_to_use = 1; + plat->rx_queues_to_use = 1;
- ret = loongson_dwmac_config_legacy(pdev, plat, &res, np); + ret = loongson_dwmac_config_legacy(pdev, plat, &res, np); + break; + }
/* GNET devices with dev revision 0x00 do not support manually * setting the speed to 1000. @@ -189,12 +549,10 @@ static int loongson_dwmac_probe(struct pci_dev *pdev, const struct pci_device_id
ret = stmmac_dvr_probe(&pdev->dev, plat, &res); if (ret) - goto err_disable_msi; + goto err_disable_device;
return ret;
-err_disable_msi: - pci_disable_msi(pdev); err_disable_device: pci_disable_device(pdev); err_put_node: @@ -262,6 +620,7 @@ static SIMPLE_DEV_PM_OPS(loongson_dwmac_pm_ops, loongson_dwmac_suspend,
static const struct pci_device_id loongson_dwmac_id_table[] = { { PCI_DEVICE_DATA(LOONGSON, GMAC, &loongson_gmac_pci_info) }, + { PCI_DEVICE_DATA(LOONGSON, GNET, &loongson_gnet_pci_info) }, {} }; MODULE_DEVICE_TABLE(pci, loongson_dwmac_id_table);