From: Nikolay Aleksandrov razor@blackwall.org
mainline inclusion from mainline-v6.3-rc3 commit 9ec7eb60dcbcb6c41076defbc5df7bbd95ceaba5 category: bugfix bugzilla: https://gitee.com/openeuler/kernel/issues/I6WNGK CVE: NA
Reference: https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?i...
---------------------------
Add bond_ether_setup helper which is used to fix ether_setup() calls in the bonding driver. It takes care of both IFF_MASTER and IFF_SLAVE flags, the former is always restored and the latter only if it was set. If the bond enslaves non-ARPHRD_ETHER device (changes its type), then releases it and enslaves ARPHRD_ETHER device (changes back) then we use ether_setup() to restore the bond device type but it also resets its flags and removes IFF_MASTER and IFF_SLAVE[1]. Use the bond_ether_setup helper to restore both after such transition.
[1] reproduce (nlmon is non-ARPHRD_ETHER): $ ip l add nlmon0 type nlmon $ ip l add bond2 type bond mode active-backup $ ip l set nlmon0 master bond2 $ ip l set nlmon0 nomaster $ ip l add bond1 type bond (we use bond1 as ARPHRD_ETHER device to restore bond2's mode) $ ip l set bond1 master bond2 $ ip l sh dev bond2 37: bond2: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode DEFAULT group default qlen 1000 link/ether be:d7:c5:40:5b:cc brd ff:ff:ff:ff:ff:ff promiscuity 0 minmtu 68 maxmtu 1500 (notice bond2's IFF_MASTER is missing)
Fixes: e36b9d16c6a6 ("bonding: clean muticast addresses when device changes type") Signed-off-by: Nikolay Aleksandrov razor@blackwall.org Signed-off-by: David S. Miller davem@davemloft.net Conflicts: drivers/net/bonding/bond_main.c Signed-off-by: Ziyang Xuan william.xuanziyang@huawei.com Reviewed-by: Yue Haibing yuehaibing@huawei.com Signed-off-by: Jialin Zhang zhangjialin11@huawei.com --- drivers/net/bonding/bond_main.c | 19 +++++++++++++++---- 1 file changed, 15 insertions(+), 4 deletions(-)
diff --git a/drivers/net/bonding/bond_main.c b/drivers/net/bonding/bond_main.c index 5b0a640eccf6..a5ac22cbcb2d 100644 --- a/drivers/net/bonding/bond_main.c +++ b/drivers/net/bonding/bond_main.c @@ -1690,6 +1690,19 @@ void bond_lower_state_changed(struct slave *slave) netdev_lower_state_changed(slave->dev, &info); }
+/* The bonding driver uses ether_setup() to convert a master bond device + * to ARPHRD_ETHER, that resets the target netdevice's flags so we always + * have to restore the IFF_MASTER flag, and only restore IFF_SLAVE if it was set + */ +static void bond_ether_setup(struct net_device *bond_dev) +{ + unsigned int slave_flag = bond_dev->flags & IFF_SLAVE; + + ether_setup(bond_dev); + bond_dev->flags |= IFF_MASTER | slave_flag; + bond_dev->priv_flags &= ~IFF_TX_SKB_SHARING; +} + /* enslave device <slave> to bond device <master> */ int bond_enslave(struct net_device *bond_dev, struct net_device *slave_dev, struct netlink_ext_ack *extack) @@ -1784,10 +1797,8 @@ int bond_enslave(struct net_device *bond_dev, struct net_device *slave_dev,
if (slave_dev->type != ARPHRD_ETHER) bond_setup_by_slave(bond_dev, slave_dev); - else { - ether_setup(bond_dev); - bond_dev->priv_flags &= ~IFF_TX_SKB_SHARING; - } + else + bond_ether_setup(bond_dev);
call_netdevice_notifiers(NETDEV_POST_TYPE_CHANGE, bond_dev);