From: Herve Codina herve.codina@bootlin.com
stable inclusion from stable-v5.10.85 commit 347cc9b4d9662aebc3aa7a12c12f0c8c091d1db9 bugzilla: 186032 https://gitee.com/openeuler/kernel/issues/I4QVI4
Reference: https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?id=...
--------------------------------
commit 9472335eaa1452b51dc8e8edaa1a342997cb80c7 upstream.
Under certain circumstances, the timing settings calculated by the FSMC NAND controller driver were inaccurate. These settings led to incorrect data reads or fallback to timing mode 0 depending on the NAND chip used.
The timing computation did not take into account the following constraint given in SPEAr3xx reference manual: twait >= tCEA - (tset * TCLK) + TOUTDEL + TINDEL
Enhance the timings calculation by taking into account this additional constraint.
This change has no impact on slow timing modes such as mode 0. Indeed, on mode 0, computed values are the same with and without the patch.
NANDs which previously stayed in mode 0 because of fallback to mode 0 can now work at higher speeds and NANDs which were not working at all because of the corrupted data work at high speeds without troubles.
Overall improvement on a Micron/MT29F1G08 (flash_speed tool): mode0 mode3 eraseblock write speed 3220 KiB/s 4511 KiB/s eraseblock read speed 4491 KiB/s 7529 KiB/s
Fixes: d9fb079571833 ("mtd: nand: fsmc: add support for SDR timings") Signed-off-by: Herve Codina herve.codina@bootlin.com Signed-off-by: Miquel Raynal miquel.raynal@bootlin.com Link: https://lore.kernel.org/linux-mtd/20211119150316.43080-5-herve.codina@bootli... Signed-off-by: Greg Kroah-Hartman gregkh@linuxfoundation.org Signed-off-by: Chen Jun chenjun102@huawei.com Signed-off-by: Zheng Zengkai zhengzengkai@huawei.com --- drivers/mtd/nand/raw/fsmc_nand.c | 32 ++++++++++++++++++++++++-------- 1 file changed, 24 insertions(+), 8 deletions(-)
diff --git a/drivers/mtd/nand/raw/fsmc_nand.c b/drivers/mtd/nand/raw/fsmc_nand.c index 4b657b4f1629..663ff5300ad9 100644 --- a/drivers/mtd/nand/raw/fsmc_nand.c +++ b/drivers/mtd/nand/raw/fsmc_nand.c @@ -94,6 +94,14 @@
#define FSMC_BUSY_WAIT_TIMEOUT (1 * HZ)
+/* + * According to SPEAr300 Reference Manual (RM0082) + * TOUDEL = 7ns (Output delay from the flip-flops to the board) + * TINDEL = 5ns (Input delay from the board to the flipflop) + */ +#define TOUTDEL 7000 +#define TINDEL 5000 + struct fsmc_nand_timings { u8 tclr; u8 tar; @@ -278,7 +286,7 @@ static int fsmc_calc_timings(struct fsmc_nand_data *host, { unsigned long hclk = clk_get_rate(host->clk); unsigned long hclkn = NSEC_PER_SEC / hclk; - u32 thiz, thold, twait, tset; + u32 thiz, thold, twait, tset, twait_min;
if (sdrt->tRC_min < 30000) return -EOPNOTSUPP; @@ -310,13 +318,6 @@ static int fsmc_calc_timings(struct fsmc_nand_data *host, else if (tims->thold > FSMC_THOLD_MASK) tims->thold = FSMC_THOLD_MASK;
- twait = max(sdrt->tRP_min, sdrt->tWP_min); - tims->twait = DIV_ROUND_UP(twait / 1000, hclkn) - 1; - if (tims->twait == 0) - tims->twait = 1; - else if (tims->twait > FSMC_TWAIT_MASK) - tims->twait = FSMC_TWAIT_MASK; - tset = max(sdrt->tCS_min - sdrt->tWP_min, sdrt->tCEA_max - sdrt->tREA_max); tims->tset = DIV_ROUND_UP(tset / 1000, hclkn) - 1; @@ -325,6 +326,21 @@ static int fsmc_calc_timings(struct fsmc_nand_data *host, else if (tims->tset > FSMC_TSET_MASK) tims->tset = FSMC_TSET_MASK;
+ /* + * According to SPEAr300 Reference Manual (RM0082) which gives more + * information related to FSMSC timings than the SPEAr600 one (RM0305), + * twait >= tCEA - (tset * TCLK) + TOUTDEL + TINDEL + */ + twait_min = sdrt->tCEA_max - ((tims->tset + 1) * hclkn * 1000) + + TOUTDEL + TINDEL; + twait = max3(sdrt->tRP_min, sdrt->tWP_min, twait_min); + + tims->twait = DIV_ROUND_UP(twait / 1000, hclkn) - 1; + if (tims->twait == 0) + tims->twait = 1; + else if (tims->twait > FSMC_TWAIT_MASK) + tims->twait = FSMC_TWAIT_MASK; + return 0; }