From: Xingui Yang yangxingui@huawei.com
driver inclusion category: bugfix bugzilla: https://gitee.com/openeuler/kernel/issues/IBCOG7 CVE: NA
----------------------------------------------------------------------
the SAS controller determines the disk to which I/Os are delivered based on the port id in the DQ entry when SATA disk directly connected.
When many phys were disconnected immediately and connected again during I/O sending and port id of phys were changed and used by other link, I/O may be sent to incorrect disk and data inconsistency on the SATA disk may occur during I/O retry with the old port id. So enable force phy, then force the command to be executed in a certain phy, and if the actual phy id of the port does not match the phy configured in the command, the chip will stop delivering the I/O to disk.
Signed-off-by: Xingui Yang yangxingui@huawei.com Signed-off-by: Bing Xia xiabing14@h-partners.com --- drivers/scsi/hisi_sas/hisi_sas_v2_hw.c | 9 +++++++-- drivers/scsi/hisi_sas/hisi_sas_v3_hw.c | 14 ++++++++++++-- 2 files changed, 19 insertions(+), 4 deletions(-)
diff --git a/drivers/scsi/hisi_sas/hisi_sas_v2_hw.c b/drivers/scsi/hisi_sas/hisi_sas_v2_hw.c index 59e56df322db..b00a82a2b657 100644 --- a/drivers/scsi/hisi_sas/hisi_sas_v2_hw.c +++ b/drivers/scsi/hisi_sas/hisi_sas_v2_hw.c @@ -2508,10 +2508,15 @@ static void prep_ata_v2_hw(struct hisi_hba *hisi_hba, /* create header */ /* dw0 */ dw0 = port->id << CMD_HDR_PORT_OFF; - if (parent_dev && dev_is_expander(parent_dev->dev_type)) + if (parent_dev && dev_is_expander(parent_dev->dev_type)) { dw0 |= 3 << CMD_HDR_CMD_OFF; - else + } else { + int phy_id = device->phy->identify.phy_identifier; + + dw0 |= (1U << phy_id) << CMD_HDR_PHY_ID_OFF; + dw0 |= CMD_HDR_FORCE_PHY_MSK; dw0 |= 4 << CMD_HDR_CMD_OFF; + }
if (tmf && ata_task->force_phy) { dw0 |= CMD_HDR_FORCE_PHY_MSK; diff --git a/drivers/scsi/hisi_sas/hisi_sas_v3_hw.c b/drivers/scsi/hisi_sas/hisi_sas_v3_hw.c index a86cdb6dbee6..37550e788bec 100644 --- a/drivers/scsi/hisi_sas/hisi_sas_v3_hw.c +++ b/drivers/scsi/hisi_sas/hisi_sas_v3_hw.c @@ -359,6 +359,10 @@ #define CMD_HDR_RESP_REPORT_MSK (0x1 << CMD_HDR_RESP_REPORT_OFF) #define CMD_HDR_TLR_CTRL_OFF 6 #define CMD_HDR_TLR_CTRL_MSK (0x3 << CMD_HDR_TLR_CTRL_OFF) +#define CMD_HDR_PHY_ID_OFF 8 +#define CMD_HDR_PHY_ID_MSK (0x1ff << CMD_HDR_PHY_ID_OFF) +#define CMD_HDR_FORCE_PHY_OFF 17 +#define CMD_HDR_FORCE_PHY_MSK (0x1U << CMD_HDR_FORCE_PHY_OFF) #define CMD_HDR_PORT_OFF 18 #define CMD_HDR_PORT_MSK (0xf << CMD_HDR_PORT_OFF) #define CMD_HDR_PRIORITY_OFF 27 @@ -1434,10 +1438,16 @@ static void prep_ata_v3_hw(struct hisi_hba *hisi_hba, u32 dw1 = 0, dw2 = 0;
hdr->dw0 = cpu_to_le32(port->id << CMD_HDR_PORT_OFF); - if (parent_dev && dev_is_expander(parent_dev->dev_type)) + if (parent_dev && dev_is_expander(parent_dev->dev_type)) { hdr->dw0 |= cpu_to_le32(3 << CMD_HDR_CMD_OFF); - else + } else { + int phy_id = device->phy->identify.phy_identifier; + + hdr->dw0 |= cpu_to_le32((1U << phy_id) + << CMD_HDR_PHY_ID_OFF); + hdr->dw0 |= CMD_HDR_FORCE_PHY_MSK; hdr->dw0 |= cpu_to_le32(4U << CMD_HDR_CMD_OFF); + }
switch (task->data_dir) { case DMA_TO_DEVICE: