Backport 5.10.92 LTS patches from upstream.
Conflicts:
already merged(git am --skip): 35ab8c9085b0a bpf: Fix out of bounds access from invalid *_or_null type verification
Aaron Ma (2): Bluetooth: btusb: Add support for Foxconn MT7922A Bluetooth: btusb: Add support for Foxconn QCA 0xe0d0
Adrian Hunter (1): mmc: sdhci-pci: Add PCI ID for Intel ADL
Alan Stern (2): USB: core: Fix bug in resuming hub's handling of wakeup requests USB: Fix "slab-out-of-bounds Write" bug in usb_hcd_poll_rh_status
Andy Shevchenko (1): mfd: intel-lpss: Fix too early PM enablement in the ACPI ->probe()
Arnd Bergmann (1): staging: greybus: fix stack size warning with UBSAN
Brian Silverman (1): can: gs_usb: gs_can_start_xmit(): zero-initialize hf->{flags,reserved}
Daniel Borkmann (1): veth: Do not record rx queue hint in veth_xmit
Dominik Brodowski (1): random: fix crash on multiple early calls to add_bootloader_randomness()
Eric Biggers (2): random: fix data race on crng_node_pool random: fix data race on crng init time
Frederic Weisbecker (1): workqueue: Fix unbind_workers() VS wq_worker_running() race
Johan Hovold (1): Bluetooth: bfusb: fix division by zero in send path
Marc Kleine-Budde (2): can: gs_usb: fix use of uninitialized variable, detach device on reception of invalid USB data can: isotp: convert struct tpcon::{idx,len} to unsigned int
Mark-YW.Chen (1): Bluetooth: btusb: fix memory leak in btusb_mtk_submit_wmt_recv_urb()
Nathan Chancellor (2): staging: wlan-ng: Avoid bitwise vs logical OR warning in hfa384x_usb_throttlefn() drm/i915: Avoid bitwise vs logical OR warning in snb_wm_latency_quirk()
Paul Cercueil (1): ARM: dts: exynos: Fix BCM4330 Bluetooth reset polarity in I9100
Ricardo Ribalda (1): media: Revert "media: uvcvideo: Set unique vdev name based in type"
Sven Eckelmann (1): ath11k: Fix buffer overflow when scanning with extraie
Zijun Hu (1): Bluetooth: btusb: Add two more Bluetooth parts for WCN6855
arch/arm/boot/dts/exynos4210-i9100.dts | 2 +- drivers/bluetooth/bfusb.c | 3 + drivers/bluetooth/btusb.c | 22 +++++ drivers/char/random.c | 117 +++++++++++++---------- drivers/gpu/drm/i915/intel_pm.c | 6 +- drivers/media/usb/uvc/uvc_driver.c | 7 +- drivers/mfd/intel-lpss-acpi.c | 7 +- drivers/mmc/host/sdhci-pci-core.c | 1 + drivers/mmc/host/sdhci-pci.h | 1 + drivers/net/can/usb/gs_usb.c | 5 +- drivers/net/veth.c | 1 - drivers/net/wireless/ath/ath11k/wmi.c | 6 +- drivers/staging/greybus/audio_topology.c | 92 +++++++++--------- drivers/staging/wlan-ng/hfa384x_usb.c | 22 ++--- drivers/usb/core/hcd.c | 9 +- drivers/usb/core/hub.c | 2 +- kernel/workqueue.c | 9 ++ net/can/isotp.c | 4 +- 18 files changed, 190 insertions(+), 126 deletions(-)
From: Frederic Weisbecker frederic@kernel.org
stable inclusion from stable-v5.10.92 commit c84fbba8a9458aaaa7d0ccae51ef05739ded54fb bugzilla: 186193 https://gitee.com/openeuler/kernel/issues/I53108
Reference: https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?id=...
--------------------------------
commit 07edfece8bcb0580a1828d939e6f8d91a8603eb2 upstream.
At CPU-hotplug time, unbind_worker() may preempt a worker while it is waking up. In that case the following scenario can happen:
unbind_workers() wq_worker_running() -------------- ------------------- if (!(worker->flags & WORKER_NOT_RUNNING)) //PREEMPTED by unbind_workers worker->flags |= WORKER_UNBOUND; [...] atomic_set(&pool->nr_running, 0); //resume to worker atomic_inc(&worker->pool->nr_running);
After unbind_worker() resets pool->nr_running, the value is expected to remain 0 until the pool ever gets rebound in case cpu_up() is called on the target CPU in the future. But here the race leaves pool->nr_running with a value of 1, triggering the following warning when the worker goes idle:
WARNING: CPU: 3 PID: 34 at kernel/workqueue.c:1823 worker_enter_idle+0x95/0xc0 Modules linked in: CPU: 3 PID: 34 Comm: kworker/3:0 Not tainted 5.16.0-rc1+ #34 Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.12.0-59-gc9ba527-rebuilt.opensuse.org 04/01/2014 Workqueue: 0x0 (rcu_par_gp) RIP: 0010:worker_enter_idle+0x95/0xc0 Code: 04 85 f8 ff ff ff 39 c1 7f 09 48 8b 43 50 48 85 c0 74 1b 83 e2 04 75 99 8b 43 34 39 43 30 75 91 8b 83 00 03 00 00 85 c0 74 87 <0f> 0b 5b c3 48 8b 35 70 f1 37 01 48 8d 7b 48 48 81 c6 e0 93 0 RSP: 0000:ffff9b7680277ed0 EFLAGS: 00010086 RAX: 00000000ffffffff RBX: ffff93465eae9c00 RCX: 0000000000000000 RDX: 0000000000000000 RSI: ffff9346418a0000 RDI: ffff934641057140 RBP: ffff934641057170 R08: 0000000000000001 R09: ffff9346418a0080 R10: ffff9b768027fdf0 R11: 0000000000002400 R12: ffff93465eae9c20 R13: ffff93465eae9c20 R14: ffff93465eae9c70 R15: ffff934641057140 FS: 0000000000000000(0000) GS:ffff93465eac0000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000000000000000 CR3: 000000001cc0c000 CR4: 00000000000006e0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: <TASK> worker_thread+0x89/0x3d0 ? process_one_work+0x400/0x400 kthread+0x162/0x190 ? set_kthread_struct+0x40/0x40 ret_from_fork+0x22/0x30 </TASK>
Also due to this incorrect "nr_running == 1", further queued work may end up not being served, because no worker is awaken at work insert time. This raises rcutorture writer stalls for example.
Fix this with disabling preemption in the right place in wq_worker_running().
It's worth noting that if the worker migrates and runs concurrently with unbind_workers(), it is guaranteed to see the WORKER_UNBOUND flag update due to set_cpus_allowed_ptr() acquiring/releasing rq->lock.
Fixes: 6d25be5782e4 ("sched/core, workqueues: Distangle worker accounting from rq lock") Reviewed-by: Lai Jiangshan jiangshanlai@gmail.com Tested-by: Paul E. McKenney paulmck@kernel.org Acked-by: Peter Zijlstra (Intel) peterz@infradead.org Signed-off-by: Frederic Weisbecker frederic@kernel.org Cc: Thomas Gleixner tglx@linutronix.de Cc: Ingo Molnar mingo@redhat.com Cc: Sebastian Andrzej Siewior bigeasy@linutronix.de Cc: Daniel Bristot de Oliveira bristot@redhat.com Signed-off-by: Tejun Heo tj@kernel.org Signed-off-by: Greg Kroah-Hartman gregkh@linuxfoundation.org Signed-off-by: Chen Jun chenjun102@huawei.com Signed-off-by: Zheng Zengkai zhengzengkai@huawei.com Acked-by: Xie XiuQi xiexiuqi@huawei.com --- kernel/workqueue.c | 9 +++++++++ 1 file changed, 9 insertions(+)
diff --git a/kernel/workqueue.c b/kernel/workqueue.c index af95ef023e1a..6bef482a152b 100644 --- a/kernel/workqueue.c +++ b/kernel/workqueue.c @@ -850,8 +850,17 @@ void wq_worker_running(struct task_struct *task)
if (!worker->sleeping) return; + + /* + * If preempted by unbind_workers() between the WORKER_NOT_RUNNING check + * and the nr_running increment below, we may ruin the nr_running reset + * and leave with an unexpected pool->nr_running == 1 on the newly unbound + * pool. Protect against such race. + */ + preempt_disable(); if (!(worker->flags & WORKER_NOT_RUNNING)) atomic_inc(&worker->pool->nr_running); + preempt_enable(); worker->sleeping = 0; }
From: "Mark-YW.Chen" mark-yw.chen@mediatek.com
stable inclusion from stable-v5.10.92 commit 294c0dd80d8a2202fc5f883005730900e72ece58 bugzilla: 186193 https://gitee.com/openeuler/kernel/issues/I53108
Reference: https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?id=...
--------------------------------
commit 60c6a63a3d3080a62f3e0e20084f58dbeff16748 upstream.
Driver should free `usb->setup_packet` to avoid the leak.
$ cat /sys/kernel/debug/kmemleak unreferenced object 0xffffffa564a58080 (size 128): backtrace: [<000000007eb8dd70>] kmem_cache_alloc_trace+0x22c/0x384 [<000000008a44191d>] btusb_mtk_hci_wmt_sync+0x1ec/0x994 [btusb] [<00000000ca7189a3>] btusb_mtk_setup+0x6b8/0x13cc [btusb] [<00000000c6105069>] hci_dev_do_open+0x290/0x974 [bluetooth] [<00000000a583f8b8>] hci_power_on+0xdc/0x3cc [bluetooth] [<000000005d80e687>] process_one_work+0x514/0xc80 [<00000000f4d57637>] worker_thread+0x818/0xd0c [<00000000dc7bdb55>] kthread+0x2f8/0x3b8 [<00000000f9999513>] ret_from_fork+0x10/0x30
Fixes: a1c49c434e150 ("Bluetooth: btusb: Add protocol support for MediaTek MT7668U USB devices") Signed-off-by: Mark-YW.Chen mark-yw.chen@mediatek.com Signed-off-by: Marcel Holtmann marcel@holtmann.org Signed-off-by: Greg Kroah-Hartman gregkh@linuxfoundation.org Signed-off-by: Chen Jun chenjun102@huawei.com Signed-off-by: Zheng Zengkai zhengzengkai@huawei.com Acked-by: Xie XiuQi xiexiuqi@huawei.com --- drivers/bluetooth/btusb.c | 5 +++++ 1 file changed, 5 insertions(+)
diff --git a/drivers/bluetooth/btusb.c b/drivers/bluetooth/btusb.c index e0859f4e2807..589ac48584a9 100644 --- a/drivers/bluetooth/btusb.c +++ b/drivers/bluetooth/btusb.c @@ -2845,6 +2845,7 @@ static void btusb_mtk_wmt_recv(struct urb *urb) skb = bt_skb_alloc(HCI_WMT_MAX_EVENT_SIZE, GFP_ATOMIC); if (!skb) { hdev->stat.err_rx++; + kfree(urb->setup_packet); return; }
@@ -2865,6 +2866,7 @@ static void btusb_mtk_wmt_recv(struct urb *urb) data->evt_skb = skb_clone(skb, GFP_ATOMIC); if (!data->evt_skb) { kfree_skb(skb); + kfree(urb->setup_packet); return; } } @@ -2873,6 +2875,7 @@ static void btusb_mtk_wmt_recv(struct urb *urb) if (err < 0) { kfree_skb(data->evt_skb); data->evt_skb = NULL; + kfree(urb->setup_packet); return; }
@@ -2883,6 +2886,7 @@ static void btusb_mtk_wmt_recv(struct urb *urb) wake_up_bit(&data->flags, BTUSB_TX_WAIT_VND_EVT); } + kfree(urb->setup_packet); return; } else if (urb->status == -ENOENT) { /* Avoid suspend failed when usb_kill_urb */ @@ -2903,6 +2907,7 @@ static void btusb_mtk_wmt_recv(struct urb *urb) usb_anchor_urb(urb, &data->ctrl_anchor); err = usb_submit_urb(urb, GFP_ATOMIC); if (err < 0) { + kfree(urb->setup_packet); /* -EPERM: urb is being killed; * -ENODEV: device got disconnected */
From: Zijun Hu quic_zijuhu@quicinc.com
stable inclusion from stable-v5.10.92 commit 83493918380f6da219113967da7cb5bfb5d2e25e bugzilla: 186193 https://gitee.com/openeuler/kernel/issues/I53108
Reference: https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?id=...
--------------------------------
commit d2666be51d5f09662929888dd84d1f4d38c97127 upstream.
Add USB IDs (0x10ab, 0x9309) and (0x10ab, 0x9409) to usb_device_id table for WCN6855.
* /sys/kernel/debug/usb/devices T: Bus=02 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 10 Spd=12 MxCh= 0 D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=10ab ProdID=9309 Rev= 0.01 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms I: If#= 1 Alt= 7 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 65 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 65 Ivl=1ms
T: Bus=02 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 11 Spd=12 MxCh= 0 D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=10ab ProdID=9409 Rev= 0.01 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms I: If#= 1 Alt= 7 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 65 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 65 Ivl=1ms
Signed-off-by: Zijun Hu quic_zijuhu@quicinc.com Signed-off-by: Marcel Holtmann marcel@holtmann.org Signed-off-by: Luiz Augusto von Dentz luiz.von.dentz@intel.com Signed-off-by: Greg Kroah-Hartman gregkh@linuxfoundation.org Signed-off-by: Chen Jun chenjun102@huawei.com Signed-off-by: Zheng Zengkai zhengzengkai@huawei.com Acked-by: Xie XiuQi xiexiuqi@huawei.com --- drivers/bluetooth/btusb.c | 6 ++++++ 1 file changed, 6 insertions(+)
diff --git a/drivers/bluetooth/btusb.c b/drivers/bluetooth/btusb.c index 589ac48584a9..4a4542691ad1 100644 --- a/drivers/bluetooth/btusb.c +++ b/drivers/bluetooth/btusb.c @@ -379,6 +379,12 @@ static const struct usb_device_id blacklist_table[] = { { USB_DEVICE(0x8087, 0x0aaa), .driver_info = BTUSB_INTEL_NEW | BTUSB_WIDEBAND_SPEECH | BTUSB_VALID_LE_STATES }, + { USB_DEVICE(0x10ab, 0x9309), .driver_info = BTUSB_QCA_WCN6855 | + BTUSB_WIDEBAND_SPEECH | + BTUSB_VALID_LE_STATES }, + { USB_DEVICE(0x10ab, 0x9409), .driver_info = BTUSB_QCA_WCN6855 | + BTUSB_WIDEBAND_SPEECH | + BTUSB_VALID_LE_STATES },
/* Other Intel Bluetooth devices */ { USB_VENDOR_AND_INTERFACE_INFO(0x8087, 0xe0, 0x01, 0x01),
From: Aaron Ma aaron.ma@canonical.com
stable inclusion from stable-v5.10.92 commit c20021ce945f38e8597551687fdb115bfca7ae86 bugzilla: 186193 https://gitee.com/openeuler/kernel/issues/I53108
Reference: https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?id=...
--------------------------------
commit 6932627425d6d3849aecd43c02158a5312895ad4 upstream.
Add 2 USB IDs for MT7922A chip. These 2 devices got the same description.
T: Bus=01 Lev=01 Prnt=01 Port=02 Cnt=01 Dev#= 2 Spd=480 MxCh= 0 D: Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0489 ProdID=e0d8 Rev= 1.00
T: Bus=03 Lev=01 Prnt=01 Port=02 Cnt=02 Dev#= 3 Spd=480 MxCh= 0 D: Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0489 ProdID=e0d9 Rev= 1.00 S: Manufacturer=MediaTek Inc. S: Product=Wireless_Device S: SerialNumber=000000000 C:* #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr=100mA A: FirstIf#= 0 IfCount= 3 Cls=e0(wlcon) Sub=01 Prot=01 I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=125us E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms I:* If#= 2 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none) E: Ad=8a(I) Atr=03(Int.) MxPS= 64 Ivl=125us E: Ad=0a(O) Atr=03(Int.) MxPS= 64 Ivl=125us I: If#= 2 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none) E: Ad=8a(I) Atr=03(Int.) MxPS= 512 Ivl=125us E: Ad=0a(O) Atr=03(Int.) MxPS= 512 Ivl=125us
Signed-off-by: Aaron Ma aaron.ma@canonical.com Signed-off-by: Marcel Holtmann marcel@holtmann.org Signed-off-by: Greg Kroah-Hartman gregkh@linuxfoundation.org Signed-off-by: Chen Jun chenjun102@huawei.com Signed-off-by: Zheng Zengkai zhengzengkai@huawei.com Acked-by: Xie XiuQi xiexiuqi@huawei.com --- drivers/bluetooth/btusb.c | 8 ++++++++ 1 file changed, 8 insertions(+)
diff --git a/drivers/bluetooth/btusb.c b/drivers/bluetooth/btusb.c index 4a4542691ad1..5a3c6b25308a 100644 --- a/drivers/bluetooth/btusb.c +++ b/drivers/bluetooth/btusb.c @@ -406,6 +406,14 @@ static const struct usb_device_id blacklist_table[] = { BTUSB_WIDEBAND_SPEECH | BTUSB_VALID_LE_STATES },
+ /* MediaTek MT7922A Bluetooth devices */ + { USB_DEVICE(0x0489, 0xe0d8), .driver_info = BTUSB_MEDIATEK | + BTUSB_WIDEBAND_SPEECH | + BTUSB_VALID_LE_STATES }, + { USB_DEVICE(0x0489, 0xe0d9), .driver_info = BTUSB_MEDIATEK | + BTUSB_WIDEBAND_SPEECH | + BTUSB_VALID_LE_STATES }, + /* Additional Realtek 8723AE Bluetooth devices */ { USB_DEVICE(0x0930, 0x021d), .driver_info = BTUSB_REALTEK }, { USB_DEVICE(0x13d3, 0x3394), .driver_info = BTUSB_REALTEK },
From: Aaron Ma aaron.ma@canonical.com
stable inclusion from stable-v5.10.92 commit 869e1677a058db069911ed2c4e2f55772bc213fe bugzilla: 186193 https://gitee.com/openeuler/kernel/issues/I53108
Reference: https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?id=...
--------------------------------
commit 1cd563ebd0dc062127a85e84f934f4c697bb43ef upstream.
Add an ID of Qualcomm Bluetooth SoC WCN6855.
T: Bus=05 Lev=01 Prnt=01 Port=03 Cnt=02 Dev#= 4 Spd=12 MxCh= 0 D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0489 ProdID=e0d0 Rev= 0.01 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I: If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I:* If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms I: If#= 1 Alt= 7 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 65 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 65 Ivl=1ms
Signed-off-by: Aaron Ma aaron.ma@canonical.com Signed-off-by: Marcel Holtmann marcel@holtmann.org Signed-off-by: Greg Kroah-Hartman gregkh@linuxfoundation.org Signed-off-by: Chen Jun chenjun102@huawei.com Signed-off-by: Zheng Zengkai zhengzengkai@huawei.com Acked-by: Xie XiuQi xiexiuqi@huawei.com --- drivers/bluetooth/btusb.c | 3 +++ 1 file changed, 3 insertions(+)
diff --git a/drivers/bluetooth/btusb.c b/drivers/bluetooth/btusb.c index 5a3c6b25308a..538232b4c42a 100644 --- a/drivers/bluetooth/btusb.c +++ b/drivers/bluetooth/btusb.c @@ -385,6 +385,9 @@ static const struct usb_device_id blacklist_table[] = { { USB_DEVICE(0x10ab, 0x9409), .driver_info = BTUSB_QCA_WCN6855 | BTUSB_WIDEBAND_SPEECH | BTUSB_VALID_LE_STATES }, + { USB_DEVICE(0x0489, 0xe0d0), .driver_info = BTUSB_QCA_WCN6855 | + BTUSB_WIDEBAND_SPEECH | + BTUSB_VALID_LE_STATES },
/* Other Intel Bluetooth devices */ { USB_VENDOR_AND_INTERFACE_INFO(0x8087, 0xe0, 0x01, 0x01),
From: Johan Hovold johan@kernel.org
stable inclusion from stable-v5.10.92 commit b6dd0702369945f3b08abe991910f20b6ec281ff bugzilla: 186193 https://gitee.com/openeuler/kernel/issues/I53108
Reference: https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?id=...
--------------------------------
commit b5e6fa7a12572c82f1e7f2f51fbb02a322291291 upstream.
Add the missing bulk-out endpoint sanity check to probe() to avoid division by zero in bfusb_send_frame() in case a malicious device has broken descriptors (or when doing descriptor fuzz testing).
Note that USB core will reject URBs submitted for endpoints with zero wMaxPacketSize but that drivers doing packet-size calculations still need to handle this (cf. commit 2548288b4fb0 ("USB: Fix: Don't skip endpoint descriptors with maxpacket=0")).
Cc: stable@vger.kernel.org Signed-off-by: Johan Hovold johan@kernel.org Signed-off-by: Marcel Holtmann marcel@holtmann.org Signed-off-by: Greg Kroah-Hartman gregkh@linuxfoundation.org Signed-off-by: Chen Jun chenjun102@huawei.com Signed-off-by: Zheng Zengkai zhengzengkai@huawei.com Acked-by: Xie XiuQi xiexiuqi@huawei.com --- drivers/bluetooth/bfusb.c | 3 +++ 1 file changed, 3 insertions(+)
diff --git a/drivers/bluetooth/bfusb.c b/drivers/bluetooth/bfusb.c index 5a321b4076aa..cab93935cc7f 100644 --- a/drivers/bluetooth/bfusb.c +++ b/drivers/bluetooth/bfusb.c @@ -628,6 +628,9 @@ static int bfusb_probe(struct usb_interface *intf, const struct usb_device_id *i data->bulk_out_ep = bulk_out_ep->desc.bEndpointAddress; data->bulk_pkt_size = le16_to_cpu(bulk_out_ep->desc.wMaxPacketSize);
+ if (!data->bulk_pkt_size) + goto done; + rwlock_init(&data->lock);
data->reassembly = NULL;
From: Paul Cercueil paul@crapouillou.net
stable inclusion from stable-v5.10.92 commit 413108ce3b569d3ccfee88ff6d570f0af4801460 bugzilla: 186193 https://gitee.com/openeuler/kernel/issues/I53108
Reference: https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?id=...
--------------------------------
commit 9cb6de45a006a9799ec399bce60d64b6d4fcc4af upstream.
The reset GPIO was marked active-high, which is against what's specified in the documentation. Mark the reset GPIO as active-low. With this change, Bluetooth can now be used on the i9100.
Fixes: 8620cc2f99b7 ("ARM: dts: exynos: Add devicetree file for the Galaxy S2") Cc: stable@vger.kernel.org Signed-off-by: Paul Cercueil paul@crapouillou.net Link: https://lore.kernel.org/r/20211031234137.87070-1-paul@crapouillou.net Signed-off-by: Krzysztof Kozlowski krzysztof.kozlowski@canonical.com Signed-off-by: Greg Kroah-Hartman gregkh@linuxfoundation.org Signed-off-by: Chen Jun chenjun102@huawei.com Signed-off-by: Zheng Zengkai zhengzengkai@huawei.com Acked-by: Xie XiuQi xiexiuqi@huawei.com --- arch/arm/boot/dts/exynos4210-i9100.dts | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/arch/arm/boot/dts/exynos4210-i9100.dts b/arch/arm/boot/dts/exynos4210-i9100.dts index 7777bf51a6e6..ecc9d4dc707e 100644 --- a/arch/arm/boot/dts/exynos4210-i9100.dts +++ b/arch/arm/boot/dts/exynos4210-i9100.dts @@ -765,7 +765,7 @@ compatible = "brcm,bcm4330-bt";
shutdown-gpios = <&gpl0 4 GPIO_ACTIVE_HIGH>; - reset-gpios = <&gpl1 0 GPIO_ACTIVE_HIGH>; + reset-gpios = <&gpl1 0 GPIO_ACTIVE_LOW>; device-wakeup-gpios = <&gpx3 1 GPIO_ACTIVE_HIGH>; host-wakeup-gpios = <&gpx2 6 GPIO_ACTIVE_HIGH>; };
From: Alan Stern stern@rowland.harvard.edu
stable inclusion from stable-v5.10.92 commit 15982330b61d7d6aa53580aaff18d8db2972c094 bugzilla: 186193 https://gitee.com/openeuler/kernel/issues/I53108
Reference: https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?id=...
--------------------------------
commit 0f663729bb4afc92a9986b66131ebd5b8a9254d1 upstream.
Bugzilla #213839 reports a 7-port hub that doesn't work properly when devices are plugged into some of the ports; the kernel goes into an unending disconnect/reinitialize loop as shown in the bug report.
This "7-port hub" comprises two four-port hubs with one plugged into the other; the failures occur when a device is plugged into one of the downstream hub's ports. (These hubs have other problems too. For example, they bill themselves as USB-2.0 compliant but they only run at full speed.)
It turns out that the failures are caused by bugs in both the kernel and the hub. The hub's bug is that it reports a different bmAttributes value in its configuration descriptor following a remote wakeup (0xe0 before, 0xc0 after -- the wakeup-support bit has changed).
The kernel's bug is inside the hub driver's resume handler. When hub_activate() sees that one of the hub's downstream ports got a wakeup request from a child device, it notes this fact by setting the corresponding bit in the hub->change_bits variable. But this variable is meant for connection changes, not wakeup events; setting it causes the driver to believe the downstream port has been disconnected and then connected again (in addition to having received a wakeup request).
Because of this, the hub driver then tries to check whether the device currently plugged into the downstream port is the same as the device that had been attached there before. Normally this check succeeds and wakeup handling continues with no harm done (which is why the bug remained undetected until now). But with these dodgy hubs, the check fails because the config descriptor has changed. This causes the hub driver to reinitialize the child device, leading to the disconnect/reinitialize loop described in the bug report.
The proper way to note reception of a downstream wakeup request is to set a bit in the hub->event_bits variable instead of hub->change_bits. That way the hub driver will realize that something has happened to the port but will not think the port and child device have been disconnected. This patch makes that change.
Cc: stable@vger.kernel.org Tested-by: Jonathan McDowell noodles@earth.li Signed-off-by: Alan Stern stern@rowland.harvard.edu Link: https://lore.kernel.org/r/YdCw7nSfWYPKWQoD@rowland.harvard.edu Signed-off-by: Greg Kroah-Hartman gregkh@linuxfoundation.org Signed-off-by: Chen Jun chenjun102@huawei.com Signed-off-by: Zheng Zengkai zhengzengkai@huawei.com Acked-by: Xie XiuQi xiexiuqi@huawei.com --- drivers/usb/core/hub.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/drivers/usb/core/hub.c b/drivers/usb/core/hub.c index 3f406519da58..af15dbe6bb14 100644 --- a/drivers/usb/core/hub.c +++ b/drivers/usb/core/hub.c @@ -1224,7 +1224,7 @@ static void hub_activate(struct usb_hub *hub, enum hub_activation_type type) */ if (portchange || (hub_is_superspeed(hub->hdev) && port_resumed)) - set_bit(port1, hub->change_bits); + set_bit(port1, hub->event_bits);
} else if (udev->persist_enabled) { #ifdef CONFIG_PM
From: Alan Stern stern@rowland.harvard.edu
stable inclusion from stable-v5.10.92 commit a87cecf94375926e47c292c121fdbf3d3abd4782 bugzilla: 186193 https://gitee.com/openeuler/kernel/issues/I53108
Reference: https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?id=...
--------------------------------
commit 1d7d4c07932e04355d6e6528d44a2f2c9e354346 upstream.
When the USB core code for getting root-hub status reports was originally written, it was assumed that the hub driver would be its only caller. But this isn't true now; user programs can use usbfs to communicate with root hubs and get status reports. When they do this, they may use a transfer_buffer that is smaller than the data returned by the HCD, which will lead to a buffer overflow error when usb_hcd_poll_rh_status() tries to store the status data. This was discovered by syzbot:
BUG: KASAN: slab-out-of-bounds in memcpy include/linux/fortify-string.h:225 [inline] BUG: KASAN: slab-out-of-bounds in usb_hcd_poll_rh_status+0x5f4/0x780 drivers/usb/core/hcd.c:776 Write of size 2 at addr ffff88801da403c0 by task syz-executor133/4062
This patch fixes the bug by reducing the amount of status data if it won't fit in the transfer_buffer. If some data gets discarded then the URB's completion status is set to -EOVERFLOW rather than 0, to let the user know what happened.
Reported-and-tested-by: syzbot+3ae6a2b06f131ab9849f@syzkaller.appspotmail.com Signed-off-by: Alan Stern stern@rowland.harvard.edu Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/Yc+3UIQJ2STbxNua@rowland.harvard.edu Signed-off-by: Greg Kroah-Hartman gregkh@linuxfoundation.org Signed-off-by: Chen Jun chenjun102@huawei.com Signed-off-by: Zheng Zengkai zhengzengkai@huawei.com Acked-by: Xie XiuQi xiexiuqi@huawei.com --- drivers/usb/core/hcd.c | 9 ++++++++- 1 file changed, 8 insertions(+), 1 deletion(-)
diff --git a/drivers/usb/core/hcd.c b/drivers/usb/core/hcd.c index 99908d8d2dd3..b2710015493a 100644 --- a/drivers/usb/core/hcd.c +++ b/drivers/usb/core/hcd.c @@ -754,6 +754,7 @@ void usb_hcd_poll_rh_status(struct usb_hcd *hcd) { struct urb *urb; int length; + int status; unsigned long flags; char buffer[6]; /* Any root hubs with > 31 ports? */
@@ -771,11 +772,17 @@ void usb_hcd_poll_rh_status(struct usb_hcd *hcd) if (urb) { clear_bit(HCD_FLAG_POLL_PENDING, &hcd->flags); hcd->status_urb = NULL; + if (urb->transfer_buffer_length >= length) { + status = 0; + } else { + status = -EOVERFLOW; + length = urb->transfer_buffer_length; + } urb->actual_length = length; memcpy(urb->transfer_buffer, buffer, length);
usb_hcd_unlink_urb_from_ep(hcd, urb); - usb_hcd_giveback_urb(hcd, urb, 0); + usb_hcd_giveback_urb(hcd, urb, status); } else { length = 0; set_bit(HCD_FLAG_POLL_PENDING, &hcd->flags);
From: Sven Eckelmann sven@narfation.org
stable inclusion from stable-v5.10.92 commit 2e691f9894ccbc6186898ada8f801187178448de bugzilla: 186193 https://gitee.com/openeuler/kernel/issues/I53108
Reference: https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?id=...
--------------------------------
commit a658c929ded7ea3aee324c8c2a9635a5e5a38e7f upstream.
If cfg80211 is providing extraie's for a scanning process then ath11k will copy that over to the firmware. The extraie.len is a 32 bit value in struct element_info and describes the amount of bytes for the vendor information elements.
The WMI_TLV packet is having a special WMI_TAG_ARRAY_BYTE section. This section can have a (payload) length up to 65535 bytes because the WMI_TLV_LEN can store up to 16 bits. The code was missing such a check and could have created a scan request which cannot be parsed correctly by the firmware.
But the bigger problem was the allocation of the buffer. It has to align the TLV sections by 4 bytes. But the code was using an u8 to store the newly calculated length of this section (with alignment). And the new calculated length was then used to allocate the skbuff. But the actual code to copy in the data is using the extraie.len and not the calculated "aligned" length.
The length of extraie with IEEE80211_HW_SINGLE_SCAN_ON_ALL_BANDS enabled was 264 bytes during tests with a QCA Milan card. But it only allocated 8 bytes (264 bytes % 256) for it. As consequence, the code to memcpy the extraie into the skb was then just overwriting data after skb->end. Things like shinfo were therefore corrupted. This could usually be seen by a crash in skb_zcopy_clear which tried to call a ubuf_info callback (using a bogus address).
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-02892.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Cc: stable@vger.kernel.org Fixes: d5c65159f289 ("ath11k: driver for Qualcomm IEEE 802.11ax devices") Signed-off-by: Sven Eckelmann sven@narfation.org Signed-off-by: Kalle Valo quic_kvalo@quicinc.com Link: https://lore.kernel.org/r/20211207142913.1734635-1-sven@narfation.org Signed-off-by: Greg Kroah-Hartman gregkh@linuxfoundation.org Signed-off-by: Chen Jun chenjun102@huawei.com Signed-off-by: Zheng Zengkai zhengzengkai@huawei.com Acked-by: Xie XiuQi xiexiuqi@huawei.com --- drivers/net/wireless/ath/ath11k/wmi.c | 6 +++--- 1 file changed, 3 insertions(+), 3 deletions(-)
diff --git a/drivers/net/wireless/ath/ath11k/wmi.c b/drivers/net/wireless/ath/ath11k/wmi.c index 74ebe8e7d1d8..e84127165d85 100644 --- a/drivers/net/wireless/ath/ath11k/wmi.c +++ b/drivers/net/wireless/ath/ath11k/wmi.c @@ -2036,7 +2036,7 @@ int ath11k_wmi_send_scan_start_cmd(struct ath11k *ar, void *ptr; int i, ret, len; u32 *tmp_ptr; - u8 extraie_len_with_pad = 0; + u16 extraie_len_with_pad = 0; struct hint_short_ssid *s_ssid = NULL; struct hint_bssid *hint_bssid = NULL;
@@ -2055,7 +2055,7 @@ int ath11k_wmi_send_scan_start_cmd(struct ath11k *ar, len += sizeof(*bssid) * params->num_bssid;
len += TLV_HDR_SIZE; - if (params->extraie.len) + if (params->extraie.len && params->extraie.len <= 0xFFFF) extraie_len_with_pad = roundup(params->extraie.len, sizeof(u32)); len += extraie_len_with_pad; @@ -2162,7 +2162,7 @@ int ath11k_wmi_send_scan_start_cmd(struct ath11k *ar, FIELD_PREP(WMI_TLV_LEN, len); ptr += TLV_HDR_SIZE;
- if (params->extraie.len) + if (extraie_len_with_pad) memcpy(ptr, params->extraie.ptr, params->extraie.len);
From: Adrian Hunter adrian.hunter@intel.com
stable inclusion from stable-v5.10.92 commit ddfa53825f3d624f1cd6d3e176a37169c7700a3b bugzilla: 186193 https://gitee.com/openeuler/kernel/issues/I53108
Reference: https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?id=...
--------------------------------
commit e53e97f805cb1abeea000a61549d42f92cb10804 upstream.
Add PCI ID for Intel ADL eMMC host controller.
Signed-off-by: Adrian Hunter adrian.hunter@intel.com Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20211124094850.1783220-1-adrian.hunter@intel.com Signed-off-by: Ulf Hansson ulf.hansson@linaro.org Signed-off-by: Greg Kroah-Hartman gregkh@linuxfoundation.org Signed-off-by: Chen Jun chenjun102@huawei.com Signed-off-by: Zheng Zengkai zhengzengkai@huawei.com Acked-by: Xie XiuQi xiexiuqi@huawei.com --- drivers/mmc/host/sdhci-pci-core.c | 1 + drivers/mmc/host/sdhci-pci.h | 1 + 2 files changed, 2 insertions(+)
diff --git a/drivers/mmc/host/sdhci-pci-core.c b/drivers/mmc/host/sdhci-pci-core.c index bf04a08eeba1..a78b060ce847 100644 --- a/drivers/mmc/host/sdhci-pci-core.c +++ b/drivers/mmc/host/sdhci-pci-core.c @@ -1932,6 +1932,7 @@ static const struct pci_device_id pci_ids[] = { SDHCI_PCI_DEVICE(INTEL, JSL_SD, intel_byt_sd), SDHCI_PCI_DEVICE(INTEL, LKF_EMMC, intel_glk_emmc), SDHCI_PCI_DEVICE(INTEL, LKF_SD, intel_byt_sd), + SDHCI_PCI_DEVICE(INTEL, ADL_EMMC, intel_glk_emmc), SDHCI_PCI_DEVICE(O2, 8120, o2), SDHCI_PCI_DEVICE(O2, 8220, o2), SDHCI_PCI_DEVICE(O2, 8221, o2), diff --git a/drivers/mmc/host/sdhci-pci.h b/drivers/mmc/host/sdhci-pci.h index 8f90c4163bb5..dcd99d5057ee 100644 --- a/drivers/mmc/host/sdhci-pci.h +++ b/drivers/mmc/host/sdhci-pci.h @@ -59,6 +59,7 @@ #define PCI_DEVICE_ID_INTEL_JSL_SD 0x4df8 #define PCI_DEVICE_ID_INTEL_LKF_EMMC 0x98c4 #define PCI_DEVICE_ID_INTEL_LKF_SD 0x98f8 +#define PCI_DEVICE_ID_INTEL_ADL_EMMC 0x54c4
#define PCI_DEVICE_ID_SYSKONNECT_8000 0x8000 #define PCI_DEVICE_ID_VIA_95D0 0x95d0
From: Daniel Borkmann daniel@iogearbox.net
stable inclusion from stable-v5.10.92 commit 5f76445a31b79be85b337cce5f35affb77cc18fc bugzilla: 186193 https://gitee.com/openeuler/kernel/issues/I53108
Reference: https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?id=...
--------------------------------
commit 710ad98c363a66a0cd8526465426c5c5f8377ee0 upstream.
Laurent reported that they have seen a significant amount of TCP retransmissions at high throughput from applications residing in network namespaces talking to the outside world via veths. The drops were seen on the qdisc layer (fq_codel, as per systemd default) of the phys device such as ena or virtio_net due to all traffic hitting a _single_ TX queue _despite_ multi-queue device. (Note that the setup was _not_ using XDP on veths as the issue is generic.)
More specifically, after edbea9220251 ("veth: Store queue_mapping independently of XDP prog presence") which made it all the way back to v4.19.184+, skb_record_rx_queue() would set skb->queue_mapping to 1 (given 1 RX and 1 TX queue by default for veths) instead of leaving at 0.
This is eventually retained and callbacks like ena_select_queue() will also pick single queue via netdev_core_pick_tx()'s ndo_select_queue() once all the traffic is forwarded to that device via upper stack or other means. Similarly, for others not implementing ndo_select_queue() if XPS is disabled, netdev_pick_tx() might call into the skb_tx_hash() and check for prior skb_rx_queue_recorded() as well.
In general, it is a _bad_ idea for virtual devices like veth to mess around with queue selection [by default]. Given dev->real_num_tx_queues is by default 1, the skb->queue_mapping was left untouched, and so prior to edbea9220251 the netdev_core_pick_tx() could do its job upon __dev_queue_xmit() on the phys device.
Unbreak this and restore prior behavior by removing the skb_record_rx_queue() from veth_xmit() altogether.
If the veth peer has an XDP program attached, then it would return the first RX queue index in xdp_md->rx_queue_index (unless configured in non-default manner). However, this is still better than breaking the generic case.
Fixes: edbea9220251 ("veth: Store queue_mapping independently of XDP prog presence") Fixes: 638264dc9022 ("veth: Support per queue XDP ring") Reported-by: Laurent Bernaille laurent.bernaille@datadoghq.com Signed-off-by: Daniel Borkmann daniel@iogearbox.net Cc: Maciej Fijalkowski maciej.fijalkowski@intel.com Cc: Toshiaki Makita toshiaki.makita1@gmail.com Cc: Eric Dumazet eric.dumazet@gmail.com Cc: Paolo Abeni pabeni@redhat.com Cc: John Fastabend john.fastabend@gmail.com Cc: Willem de Bruijn willemb@google.com Acked-by: John Fastabend john.fastabend@gmail.com Reviewed-by: Eric Dumazet edumazet@google.com Acked-by: Toshiaki Makita toshiaki.makita1@gmail.com Signed-off-by: David S. Miller davem@davemloft.net Signed-off-by: Greg Kroah-Hartman gregkh@linuxfoundation.org Signed-off-by: Chen Jun chenjun102@huawei.com Signed-off-by: Zheng Zengkai zhengzengkai@huawei.com Acked-by: Xie XiuQi xiexiuqi@huawei.com --- drivers/net/veth.c | 1 - 1 file changed, 1 deletion(-)
diff --git a/drivers/net/veth.c b/drivers/net/veth.c index be18b243642f..aef66f8eecee 100644 --- a/drivers/net/veth.c +++ b/drivers/net/veth.c @@ -301,7 +301,6 @@ static netdev_tx_t veth_xmit(struct sk_buff *skb, struct net_device *dev) if (rxq < rcv->real_num_rx_queues) { rq = &rcv_priv->rq[rxq]; rcv_xdp = rcu_access_pointer(rq->xdp_prog); - skb_record_rx_queue(skb, rxq); }
skb_tx_timestamp(skb);
From: Andy Shevchenko andriy.shevchenko@linux.intel.com
stable inclusion from stable-v5.10.92 commit f68e600017354e75e696b2c6883c64bfa0072c67 bugzilla: 186193 https://gitee.com/openeuler/kernel/issues/I53108
Reference: https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?id=...
--------------------------------
commit c9e143084d1a602f829115612e1ec79df3727c8b upstream.
The runtime PM callback may be called as soon as the runtime PM facility is enabled and activated. It means that ->suspend() may be called before we finish probing the device in the ACPI case. Hence, NULL pointer dereference:
intel-lpss INT34BA:00: IRQ index 0 not found BUG: kernel NULL pointer dereference, address: 0000000000000030 ... Workqueue: pm pm_runtime_work RIP: 0010:intel_lpss_suspend+0xb/0x40 [intel_lpss]
To fix this, first try to register the device and only after that enable runtime PM facility.
Fixes: 4b45efe85263 ("mfd: Add support for Intel Sunrisepoint LPSS devices") Reported-by: Orlando Chamberlain redecorating@protonmail.com Reported-by: Aditya Garg gargaditya08@live.com Signed-off-by: Andy Shevchenko andriy.shevchenko@linux.intel.com Tested-by: Aditya Garg gargaditya08@live.com Signed-off-by: Lee Jones lee.jones@linaro.org Link: https://lore.kernel.org/r/20211101190008.86473-1-andriy.shevchenko@linux.int... Signed-off-by: Greg Kroah-Hartman gregkh@linuxfoundation.org Signed-off-by: Chen Jun chenjun102@huawei.com Signed-off-by: Zheng Zengkai zhengzengkai@huawei.com Acked-by: Xie XiuQi xiexiuqi@huawei.com --- drivers/mfd/intel-lpss-acpi.c | 7 ++++++- 1 file changed, 6 insertions(+), 1 deletion(-)
diff --git a/drivers/mfd/intel-lpss-acpi.c b/drivers/mfd/intel-lpss-acpi.c index c8fe334b5fe8..045cbf0cbe53 100644 --- a/drivers/mfd/intel-lpss-acpi.c +++ b/drivers/mfd/intel-lpss-acpi.c @@ -102,6 +102,7 @@ static int intel_lpss_acpi_probe(struct platform_device *pdev) { struct intel_lpss_platform_info *info; const struct acpi_device_id *id; + int ret;
id = acpi_match_device(intel_lpss_acpi_ids, &pdev->dev); if (!id) @@ -115,10 +116,14 @@ static int intel_lpss_acpi_probe(struct platform_device *pdev) info->mem = platform_get_resource(pdev, IORESOURCE_MEM, 0); info->irq = platform_get_irq(pdev, 0);
+ ret = intel_lpss_probe(&pdev->dev, info); + if (ret) + return ret; + pm_runtime_set_active(&pdev->dev); pm_runtime_enable(&pdev->dev);
- return intel_lpss_probe(&pdev->dev, info); + return 0; }
static int intel_lpss_acpi_remove(struct platform_device *pdev)
From: Marc Kleine-Budde mkl@pengutronix.de
stable inclusion from stable-v5.10.92 commit bd61ae808b1516ad577d37a256838e1665c5ffb4 bugzilla: 186193 https://gitee.com/openeuler/kernel/issues/I53108
Reference: https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?id=...
--------------------------------
commit 4a8737ff068724f509d583fef404d349adba80d6 upstream.
The received data contains the channel the received data is associated with. If the channel number is bigger than the actual number of channels assume broken or malicious USB device and shut it down.
This fixes the error found by clang:
| drivers/net/can/usb/gs_usb.c:386:6: error: variable 'dev' is used | uninitialized whenever 'if' condition is true | if (hf->channel >= GS_MAX_INTF) | ^~~~~~~~~~~~~~~~~~~~~~~~~~ | drivers/net/can/usb/gs_usb.c:474:10: note: uninitialized use occurs here | hf, dev->gs_hf_size, gs_usb_receive_bulk_callback, | ^~~
Link: https://lore.kernel.org/all/20211210091158.408326-1-mkl@pengutronix.de Fixes: d08e973a77d1 ("can: gs_usb: Added support for the GS_USB CAN devices") Cc: stable@vger.kernel.org Signed-off-by: Marc Kleine-Budde mkl@pengutronix.de Signed-off-by: Greg Kroah-Hartman gregkh@linuxfoundation.org Signed-off-by: Chen Jun chenjun102@huawei.com Signed-off-by: Zheng Zengkai zhengzengkai@huawei.com Acked-by: Xie XiuQi xiexiuqi@huawei.com --- drivers/net/can/usb/gs_usb.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-)
diff --git a/drivers/net/can/usb/gs_usb.c b/drivers/net/can/usb/gs_usb.c index 018ca3b057a3..9ee55eecadb1 100644 --- a/drivers/net/can/usb/gs_usb.c +++ b/drivers/net/can/usb/gs_usb.c @@ -320,7 +320,7 @@ static void gs_usb_receive_bulk_callback(struct urb *urb)
/* device reports out of range channel id */ if (hf->channel >= GS_MAX_INTF) - goto resubmit_urb; + goto device_detach;
dev = usbcan->canch[hf->channel];
@@ -405,6 +405,7 @@ static void gs_usb_receive_bulk_callback(struct urb *urb)
/* USB failure take down all interfaces */ if (rc == -ENODEV) { + device_detach: for (rc = 0; rc < GS_MAX_INTF; rc++) { if (usbcan->canch[rc]) netif_device_detach(usbcan->canch[rc]->netdev);
From: Marc Kleine-Budde mkl@pengutronix.de
stable inclusion from stable-v5.10.92 commit 45221a57b609fecceff5f66a016443e88ca9eb00 bugzilla: 186193 https://gitee.com/openeuler/kernel/issues/I53108
Reference: https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?id=...
--------------------------------
commit 5f33a09e769a9da0482f20a6770a342842443776 upstream.
In isotp_rcv_ff() 32 bit of data received over the network is assigned to struct tpcon::len. Later in that function the length is checked for the maximal supported length against MAX_MSG_LENGTH.
As struct tpcon::len is an "int" this check does not work, if the provided length overflows the "int".
Later on struct tpcon::idx is compared against struct tpcon::len.
To fix this problem this patch converts both struct tpcon::{idx,len} to unsigned int.
Fixes: e057dd3fc20f ("can: add ISO 15765-2:2016 transport protocol") Link: https://lore.kernel.org/all/20220105132429.1170627-1-mkl@pengutronix.de Cc: stable@vger.kernel.org Acked-by: Oliver Hartkopp socketcan@hartkopp.net Reported-by: syzbot+4c63f36709a642f801c5@syzkaller.appspotmail.com Signed-off-by: Marc Kleine-Budde mkl@pengutronix.de Signed-off-by: Greg Kroah-Hartman gregkh@linuxfoundation.org Signed-off-by: Chen Jun chenjun102@huawei.com Signed-off-by: Zheng Zengkai zhengzengkai@huawei.com Acked-by: Xie XiuQi xiexiuqi@huawei.com --- net/can/isotp.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-)
diff --git a/net/can/isotp.c b/net/can/isotp.c index 8ee580538d87..53ce5b6448a5 100644 --- a/net/can/isotp.c +++ b/net/can/isotp.c @@ -119,8 +119,8 @@ enum { };
struct tpcon { - int idx; - int len; + unsigned int idx; + unsigned int len; u32 state; u8 bs; u8 sn;
From: Brian Silverman brian.silverman@bluerivertech.com
stable inclusion from stable-v5.10.92 commit 43c494294f30a3899c07cf27f6dc76e0b8f8b133 bugzilla: 186193 https://gitee.com/openeuler/kernel/issues/I53108
Reference: https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?id=...
--------------------------------
commit 89d58aebe14a365c25ba6645414afdbf4e41cea4 upstream.
No information is deliberately sent in hf->flags in host -> device communications, but the open-source candleLight firmware echoes it back, which can result in the GS_CAN_FLAG_OVERFLOW flag being set and generating spurious ERRORFRAMEs.
While there also initialize the reserved member with 0.
Fixes: d08e973a77d1 ("can: gs_usb: Added support for the GS_USB CAN devices") Link: https://lore.kernel.org/all/20220106002952.25883-1-brian.silverman@blueriver... Link: https://github.com/candle-usb/candleLight_fw/issues/87 Cc: stable@vger.kernel.org Signed-off-by: Brian Silverman brian.silverman@bluerivertech.com [mkl: initialize the reserved member, too] Signed-off-by: Marc Kleine-Budde mkl@pengutronix.de Signed-off-by: Greg Kroah-Hartman gregkh@linuxfoundation.org Signed-off-by: Chen Jun chenjun102@huawei.com Signed-off-by: Zheng Zengkai zhengzengkai@huawei.com Acked-by: Xie XiuQi xiexiuqi@huawei.com --- drivers/net/can/usb/gs_usb.c | 2 ++ 1 file changed, 2 insertions(+)
diff --git a/drivers/net/can/usb/gs_usb.c b/drivers/net/can/usb/gs_usb.c index 9ee55eecadb1..3f759fae81fe 100644 --- a/drivers/net/can/usb/gs_usb.c +++ b/drivers/net/can/usb/gs_usb.c @@ -507,6 +507,8 @@ static netdev_tx_t gs_can_start_xmit(struct sk_buff *skb,
hf->echo_id = idx; hf->channel = dev->channel; + hf->flags = 0; + hf->reserved = 0;
cf = (struct can_frame *)skb->data;
From: Eric Biggers ebiggers@google.com
stable inclusion from stable-v5.10.92 commit 3de9478230c3e3ae0ae599847ca2ac6b7781e780 bugzilla: 186193 https://gitee.com/openeuler/kernel/issues/I53108
Reference: https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?id=...
--------------------------------
commit 5d73d1e320c3fd94ea15ba5f79301da9a8bcc7de upstream.
extract_crng() and crng_backtrack_protect() load crng_node_pool with a plain load, which causes undefined behavior if do_numa_crng_init() modifies it concurrently.
Fix this by using READ_ONCE(). Note: as per the previous discussion https://lore.kernel.org/lkml/20211219025139.31085-1-ebiggers@kernel.org/T/#u, READ_ONCE() is believed to be sufficient here, and it was requested that it be used here instead of smp_load_acquire().
Also change do_numa_crng_init() to set crng_node_pool using cmpxchg_release() instead of mb() + cmpxchg(), as the former is sufficient here but is more lightweight.
Fixes: 1e7f583af67b ("random: make /dev/urandom scalable for silly userspace programs") Cc: stable@vger.kernel.org Signed-off-by: Eric Biggers ebiggers@google.com Acked-by: Paul E. McKenney paulmck@kernel.org Signed-off-by: Jason A. Donenfeld Jason@zx2c4.com Signed-off-by: Greg Kroah-Hartman gregkh@linuxfoundation.org Signed-off-by: Chen Jun chenjun102@huawei.com Signed-off-by: Zheng Zengkai zhengzengkai@huawei.com Acked-by: Xie XiuQi xiexiuqi@huawei.com --- drivers/char/random.c | 42 ++++++++++++++++++++++-------------------- 1 file changed, 22 insertions(+), 20 deletions(-)
diff --git a/drivers/char/random.c b/drivers/char/random.c index 4d659c4fc2ed..8c39eeaced57 100644 --- a/drivers/char/random.c +++ b/drivers/char/random.c @@ -853,8 +853,8 @@ static void do_numa_crng_init(struct work_struct *work) crng_initialize_secondary(crng); pool[i] = crng; } - mb(); - if (cmpxchg(&crng_node_pool, NULL, pool)) { + /* pairs with READ_ONCE() in select_crng() */ + if (cmpxchg_release(&crng_node_pool, NULL, pool) != NULL) { for_each_node(i) kfree(pool[i]); kfree(pool); @@ -867,8 +867,26 @@ static void numa_crng_init(void) { schedule_work(&numa_crng_init_work); } + +static struct crng_state *select_crng(void) +{ + struct crng_state **pool; + int nid = numa_node_id(); + + /* pairs with cmpxchg_release() in do_numa_crng_init() */ + pool = READ_ONCE(crng_node_pool); + if (pool && pool[nid]) + return pool[nid]; + + return &primary_crng; +} #else static void numa_crng_init(void) {} + +static struct crng_state *select_crng(void) +{ + return &primary_crng; +} #endif
/* @@ -1015,15 +1033,7 @@ static void _extract_crng(struct crng_state *crng,
static void extract_crng(__u8 out[CHACHA_BLOCK_SIZE]) { - struct crng_state *crng = NULL; - -#ifdef CONFIG_NUMA - if (crng_node_pool) - crng = crng_node_pool[numa_node_id()]; - if (crng == NULL) -#endif - crng = &primary_crng; - _extract_crng(crng, out); + _extract_crng(select_crng(), out); }
/* @@ -1052,15 +1062,7 @@ static void _crng_backtrack_protect(struct crng_state *crng,
static void crng_backtrack_protect(__u8 tmp[CHACHA_BLOCK_SIZE], int used) { - struct crng_state *crng = NULL; - -#ifdef CONFIG_NUMA - if (crng_node_pool) - crng = crng_node_pool[numa_node_id()]; - if (crng == NULL) -#endif - crng = &primary_crng; - _crng_backtrack_protect(crng, tmp, used); + _crng_backtrack_protect(select_crng(), tmp, used); }
static ssize_t extract_crng_user(void __user *buf, size_t nbytes)
From: Eric Biggers ebiggers@google.com
stable inclusion from stable-v5.10.92 commit 61cca7d191c7c143bc8f3e779859f8b3d5100c89 bugzilla: 186193 https://gitee.com/openeuler/kernel/issues/I53108
Reference: https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?id=...
--------------------------------
commit 009ba8568be497c640cab7571f7bfd18345d7b24 upstream.
_extract_crng() does plain loads of crng->init_time and crng_global_init_time, which causes undefined behavior if crng_reseed() and RNDRESEEDCRNG modify these corrently.
Use READ_ONCE() and WRITE_ONCE() to make the behavior defined.
Don't fix the race on crng->init_time by protecting it with crng->lock, since it's not a problem for duplicate reseedings to occur. I.e., the lockless access with READ_ONCE() is fine.
Fixes: d848e5f8e1eb ("random: add new ioctl RNDRESEEDCRNG") Fixes: e192be9d9a30 ("random: replace non-blocking pool with a Chacha20-based CRNG") Cc: stable@vger.kernel.org Signed-off-by: Eric Biggers ebiggers@google.com Acked-by: Paul E. McKenney paulmck@kernel.org Signed-off-by: Jason A. Donenfeld Jason@zx2c4.com Signed-off-by: Greg Kroah-Hartman gregkh@linuxfoundation.org Signed-off-by: Chen Jun chenjun102@huawei.com Signed-off-by: Zheng Zengkai zhengzengkai@huawei.com Acked-by: Xie XiuQi xiexiuqi@huawei.com --- drivers/char/random.c | 17 ++++++++++------- 1 file changed, 10 insertions(+), 7 deletions(-)
diff --git a/drivers/char/random.c b/drivers/char/random.c index 8c39eeaced57..0b826f8321d5 100644 --- a/drivers/char/random.c +++ b/drivers/char/random.c @@ -990,7 +990,7 @@ static void crng_reseed(struct crng_state *crng, struct entropy_store *r) crng->state[i+4] ^= buf.key[i] ^ rv; } memzero_explicit(&buf, sizeof(buf)); - crng->init_time = jiffies; + WRITE_ONCE(crng->init_time, jiffies); spin_unlock_irqrestore(&crng->lock, flags); if (crng == &primary_crng && crng_init < 2) { invalidate_batched_entropy(); @@ -1016,12 +1016,15 @@ static void crng_reseed(struct crng_state *crng, struct entropy_store *r) static void _extract_crng(struct crng_state *crng, __u8 out[CHACHA_BLOCK_SIZE]) { - unsigned long v, flags; + unsigned long v, flags, init_time;
- if (crng_ready() && - (time_after(crng_global_init_time, crng->init_time) || - time_after(jiffies, crng->init_time + CRNG_RESEED_INTERVAL))) - crng_reseed(crng, crng == &primary_crng ? &input_pool : NULL); + if (crng_ready()) { + init_time = READ_ONCE(crng->init_time); + if (time_after(READ_ONCE(crng_global_init_time), init_time) || + time_after(jiffies, init_time + CRNG_RESEED_INTERVAL)) + crng_reseed(crng, crng == &primary_crng ? + &input_pool : NULL); + } spin_lock_irqsave(&crng->lock, flags); if (arch_get_random_long(&v)) crng->state[14] ^= v; @@ -1976,7 +1979,7 @@ static long random_ioctl(struct file *f, unsigned int cmd, unsigned long arg) if (crng_init < 2) return -ENODATA; crng_reseed(&primary_crng, &input_pool); - crng_global_init_time = jiffies - 1; + WRITE_ONCE(crng_global_init_time, jiffies - 1); return 0; default: return -EINVAL;
From: Dominik Brodowski linux@dominikbrodowski.net
stable inclusion from stable-v5.10.92 commit 9b3c761e78d53a510e56b69e625e515d9d41d0ba bugzilla: 186193 https://gitee.com/openeuler/kernel/issues/I53108
Reference: https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?id=...
--------------------------------
commit f7e67b8e803185d0aabe7f29d25a35c8be724a78 upstream.
Currently, if CONFIG_RANDOM_TRUST_BOOTLOADER is enabled, multiple calls to add_bootloader_randomness() are broken and can cause a NULL pointer dereference, as noted by Ivan T. Ivanov. This is not only a hypothetical problem, as qemu on arm64 may provide bootloader entropy via EFI and via devicetree.
On the first call to add_hwgenerator_randomness(), crng_fast_load() is executed, and if the seed is long enough, crng_init will be set to 1. On subsequent calls to add_bootloader_randomness() and then to add_hwgenerator_randomness(), crng_fast_load() will be skipped. Instead, wait_event_interruptible() and then credit_entropy_bits() will be called. If the entropy count for that second seed is large enough, that proceeds to crng_reseed().
However, both wait_event_interruptible() and crng_reseed() depends (at least in numa_crng_init()) on workqueues. Therefore, test whether system_wq is already initialized, which is a sufficient indicator that workqueue_init_early() has progressed far enough.
If we wind up hitting the !system_wq case, we later want to do what would have been done there when wqs are up, so set a flag, and do that work later from the rand_initialize() call.
Reported-by: Ivan T. Ivanov iivanov@suse.de Fixes: 18b915ac6b0a ("efi/random: Treat EFI_RNG_PROTOCOL output as bootloader randomness") Cc: stable@vger.kernel.org Signed-off-by: Dominik Brodowski linux@dominikbrodowski.net [Jason: added crng_need_done state and related logic.] Signed-off-by: Jason A. Donenfeld Jason@zx2c4.com Signed-off-by: Greg Kroah-Hartman gregkh@linuxfoundation.org Signed-off-by: Chen Jun chenjun102@huawei.com Signed-off-by: Zheng Zengkai zhengzengkai@huawei.com Acked-by: Xie XiuQi xiexiuqi@huawei.com --- drivers/char/random.c | 56 +++++++++++++++++++++++++++---------------- 1 file changed, 36 insertions(+), 20 deletions(-)
diff --git a/drivers/char/random.c b/drivers/char/random.c index 0b826f8321d5..cb96d3a070c6 100644 --- a/drivers/char/random.c +++ b/drivers/char/random.c @@ -461,6 +461,7 @@ static struct crng_state primary_crng = { * its value (from 0->1->2). */ static int crng_init = 0; +static bool crng_need_final_init = false; #define crng_ready() (likely(crng_init > 1)) static int crng_init_cnt = 0; static unsigned long crng_global_init_time = 0; @@ -838,6 +839,36 @@ static void __init crng_initialize_primary(struct crng_state *crng) crng->init_time = jiffies - CRNG_RESEED_INTERVAL - 1; }
+static void crng_finalize_init(struct crng_state *crng) +{ + if (crng != &primary_crng || crng_init >= 2) + return; + if (!system_wq) { + /* We can't call numa_crng_init until we have workqueues, + * so mark this for processing later. */ + crng_need_final_init = true; + return; + } + + invalidate_batched_entropy(); + numa_crng_init(); + crng_init = 2; + process_random_ready_list(); + wake_up_interruptible(&crng_init_wait); + kill_fasync(&fasync, SIGIO, POLL_IN); + pr_notice("crng init done\n"); + if (unseeded_warning.missed) { + pr_notice("%d get_random_xx warning(s) missed due to ratelimiting\n", + unseeded_warning.missed); + unseeded_warning.missed = 0; + } + if (urandom_warning.missed) { + pr_notice("%d urandom warning(s) missed due to ratelimiting\n", + urandom_warning.missed); + urandom_warning.missed = 0; + } +} + #ifdef CONFIG_NUMA static void do_numa_crng_init(struct work_struct *work) { @@ -992,25 +1023,7 @@ static void crng_reseed(struct crng_state *crng, struct entropy_store *r) memzero_explicit(&buf, sizeof(buf)); WRITE_ONCE(crng->init_time, jiffies); spin_unlock_irqrestore(&crng->lock, flags); - if (crng == &primary_crng && crng_init < 2) { - invalidate_batched_entropy(); - numa_crng_init(); - crng_init = 2; - process_random_ready_list(); - wake_up_interruptible(&crng_init_wait); - kill_fasync(&fasync, SIGIO, POLL_IN); - pr_notice("crng init done\n"); - if (unseeded_warning.missed) { - pr_notice("%d get_random_xx warning(s) missed due to ratelimiting\n", - unseeded_warning.missed); - unseeded_warning.missed = 0; - } - if (urandom_warning.missed) { - pr_notice("%d urandom warning(s) missed due to ratelimiting\n", - urandom_warning.missed); - urandom_warning.missed = 0; - } - } + crng_finalize_init(crng); }
static void _extract_crng(struct crng_state *crng, @@ -1805,6 +1818,8 @@ static void __init init_std_data(struct entropy_store *r) int __init rand_initialize(void) { init_std_data(&input_pool); + if (crng_need_final_init) + crng_finalize_init(&primary_crng); crng_initialize_primary(&primary_crng); crng_global_init_time = jiffies; if (ratelimit_disable) { @@ -2313,7 +2328,8 @@ void add_hwgenerator_randomness(const char *buffer, size_t count, * We'll be woken up again once below random_write_wakeup_thresh, * or when the calling thread is about to terminate. */ - wait_event_interruptible(random_write_wait, kthread_should_stop() || + wait_event_interruptible(random_write_wait, + !system_wq || kthread_should_stop() || ENTROPY_BITS(&input_pool) <= random_write_wakeup_bits); mix_pool_bytes(poolp, buffer, count); credit_entropy_bits(poolp, entropy);
From: Ricardo Ribalda ribalda@chromium.org
stable inclusion from stable-v5.10.92 commit 3609fed7ac8bdd6c9dfbb0a41bf03879944f738f bugzilla: 186193 https://gitee.com/openeuler/kernel/issues/I53108
Reference: https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?id=...
--------------------------------
commit f66dcb32af19faf49cc4a9222c3152b10c6ec84a upstream.
A lot of userspace depends on a descriptive name for vdev. Without this patch, users have a hard time figuring out which camera shall they use for their video conferencing.
This reverts commit e3f60e7e1a2b451f538f9926763432249bcf39c4.
Link: https://lore.kernel.org/linux-media/20211207003840.1212374-2-ribalda@chromiu... Cc: stable@vger.kernel.org Fixes: e3f60e7e1a2b ("media: uvcvideo: Set unique vdev name based in type") Reported-by: Nicolas Dufresne nicolas@ndufresne.ca Signed-off-by: Ricardo Ribalda ribalda@chromium.org Reviewed-by: Laurent Pinchart laurent.pinchart@ideasonboard.com Reviewed-by: Hans Verkuil hverkuil-cisco@xs4all.nl Signed-off-by: Mauro Carvalho Chehab mchehab+huawei@kernel.org Signed-off-by: Greg Kroah-Hartman gregkh@linuxfoundation.org Signed-off-by: Chen Jun chenjun102@huawei.com Signed-off-by: Zheng Zengkai zhengzengkai@huawei.com Acked-by: Xie XiuQi xiexiuqi@huawei.com --- drivers/media/usb/uvc/uvc_driver.c | 7 +------ 1 file changed, 1 insertion(+), 6 deletions(-)
diff --git a/drivers/media/usb/uvc/uvc_driver.c b/drivers/media/usb/uvc/uvc_driver.c index 447b6a198926..282f3d2388cc 100644 --- a/drivers/media/usb/uvc/uvc_driver.c +++ b/drivers/media/usb/uvc/uvc_driver.c @@ -2065,7 +2065,6 @@ int uvc_register_video_device(struct uvc_device *dev, const struct v4l2_file_operations *fops, const struct v4l2_ioctl_ops *ioctl_ops) { - const char *name; int ret;
/* Initialize the video buffers queue. */ @@ -2094,20 +2093,16 @@ int uvc_register_video_device(struct uvc_device *dev, case V4L2_BUF_TYPE_VIDEO_CAPTURE: default: vdev->device_caps = V4L2_CAP_VIDEO_CAPTURE | V4L2_CAP_STREAMING; - name = "Video Capture"; break; case V4L2_BUF_TYPE_VIDEO_OUTPUT: vdev->device_caps = V4L2_CAP_VIDEO_OUTPUT | V4L2_CAP_STREAMING; - name = "Video Output"; break; case V4L2_BUF_TYPE_META_CAPTURE: vdev->device_caps = V4L2_CAP_META_CAPTURE | V4L2_CAP_STREAMING; - name = "Metadata"; break; }
- snprintf(vdev->name, sizeof(vdev->name), "%s %u", name, - stream->header.bTerminalLink); + strscpy(vdev->name, dev->name, sizeof(vdev->name));
/* * Set the driver data before calling video_register_device, otherwise
From: Nathan Chancellor nathan@kernel.org
stable inclusion from stable-v5.10.92 commit 2d4fda471dc33a25024f65887d2e8289740a02e9 bugzilla: 186193 https://gitee.com/openeuler/kernel/issues/I53108
Reference: https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?id=...
--------------------------------
commit 502408a61f4b7eb4713f44bd77f4a48e6cb1b59a upstream.
A new warning in clang points out a place in this file where a bitwise OR is being used with boolean expressions:
In file included from drivers/staging/wlan-ng/prism2usb.c:2: drivers/staging/wlan-ng/hfa384x_usb.c:3787:7: warning: use of bitwise '|' with boolean operands [-Wbitwise-instead-of-logical] ((test_and_clear_bit(THROTTLE_RX, &hw->usb_flags) && ~^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ drivers/staging/wlan-ng/hfa384x_usb.c:3787:7: note: cast one or both operands to int to silence this warning 1 warning generated.
The comment explains that short circuiting here is undesirable, as the calls to test_and_{clear,set}_bit() need to happen for both sides of the expression.
Clang's suggestion would work to silence the warning but the readability of the expression would suffer even more. To clean up the warning and make the block more readable, use a variable for each side of the bitwise expression.
Link: https://github.com/ClangBuiltLinux/linux/issues/1478 Signed-off-by: Nathan Chancellor nathan@kernel.org Link: https://lore.kernel.org/r/20211014215703.3705371-1-nathan@kernel.org Signed-off-by: Greg Kroah-Hartman gregkh@linuxfoundation.org Signed-off-by: Chen Jun chenjun102@huawei.com Signed-off-by: Zheng Zengkai zhengzengkai@huawei.com Acked-by: Xie XiuQi xiexiuqi@huawei.com --- drivers/staging/wlan-ng/hfa384x_usb.c | 22 +++++++++++----------- 1 file changed, 11 insertions(+), 11 deletions(-)
diff --git a/drivers/staging/wlan-ng/hfa384x_usb.c b/drivers/staging/wlan-ng/hfa384x_usb.c index f2a0e16b0318..fac3f34d4a1f 100644 --- a/drivers/staging/wlan-ng/hfa384x_usb.c +++ b/drivers/staging/wlan-ng/hfa384x_usb.c @@ -3779,18 +3779,18 @@ static void hfa384x_usb_throttlefn(struct timer_list *t)
spin_lock_irqsave(&hw->ctlxq.lock, flags);
- /* - * We need to check BOTH the RX and the TX throttle controls, - * so we use the bitwise OR instead of the logical OR. - */ pr_debug("flags=0x%lx\n", hw->usb_flags); - if (!hw->wlandev->hwremoved && - ((test_and_clear_bit(THROTTLE_RX, &hw->usb_flags) && - !test_and_set_bit(WORK_RX_RESUME, &hw->usb_flags)) | - (test_and_clear_bit(THROTTLE_TX, &hw->usb_flags) && - !test_and_set_bit(WORK_TX_RESUME, &hw->usb_flags)) - )) { - schedule_work(&hw->usb_work); + if (!hw->wlandev->hwremoved) { + bool rx_throttle = test_and_clear_bit(THROTTLE_RX, &hw->usb_flags) && + !test_and_set_bit(WORK_RX_RESUME, &hw->usb_flags); + bool tx_throttle = test_and_clear_bit(THROTTLE_TX, &hw->usb_flags) && + !test_and_set_bit(WORK_TX_RESUME, &hw->usb_flags); + /* + * We need to check BOTH the RX and the TX throttle controls, + * so we use the bitwise OR instead of the logical OR. + */ + if (rx_throttle | tx_throttle) + schedule_work(&hw->usb_work); }
spin_unlock_irqrestore(&hw->ctlxq.lock, flags);
From: Nathan Chancellor nathan@kernel.org
stable inclusion from stable-v5.10.92 commit 66d21c005d9beaf874e466d63538ed37aa153c5e bugzilla: 186193 https://gitee.com/openeuler/kernel/issues/I53108
Reference: https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?id=...
--------------------------------
commit 2e70570656adfe1c5d9a29940faa348d5f132199 upstream.
A new warning in clang points out a place in this file where a bitwise OR is being used with boolean types:
drivers/gpu/drm/i915/intel_pm.c:3066:12: warning: use of bitwise '|' with boolean operands [-Wbitwise-instead-of-logical] changed = ilk_increase_wm_latency(dev_priv, dev_priv->wm.pri_latency, 12) | ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
This construct is intentional, as it allows every one of the calls to ilk_increase_wm_latency() to occur (instead of short circuiting with logical OR) while still caring about the result of each call.
To make this clearer to the compiler, use the '|=' operator to assign the result of each ilk_increase_wm_latency() call to changed, which keeps the meaning of the code the same but makes it obvious that every one of these calls is expected to happen.
Link: https://github.com/ClangBuiltLinux/linux/issues/1473 Reported-by: Nick Desaulniers ndesaulniers@google.com Signed-off-by: Nathan Chancellor nathan@kernel.org Suggested-by: Dávid Bolvanský david.bolvansky@gmail.com Reviewed-by: Nick Desaulniers ndesaulniers@google.com Signed-off-by: Ville Syrjälä ville.syrjala@linux.intel.com Link: https://patchwork.freedesktop.org/patch/msgid/20211014211916.3550122-1-natha... Signed-off-by: Greg Kroah-Hartman gregkh@linuxfoundation.org Signed-off-by: Chen Jun chenjun102@huawei.com Signed-off-by: Zheng Zengkai zhengzengkai@huawei.com Acked-by: Xie XiuQi xiexiuqi@huawei.com --- drivers/gpu/drm/i915/intel_pm.c | 6 +++--- 1 file changed, 3 insertions(+), 3 deletions(-)
diff --git a/drivers/gpu/drm/i915/intel_pm.c b/drivers/gpu/drm/i915/intel_pm.c index 1f23cb6ece58..e51ca7ca0a2a 100644 --- a/drivers/gpu/drm/i915/intel_pm.c +++ b/drivers/gpu/drm/i915/intel_pm.c @@ -3044,9 +3044,9 @@ static void snb_wm_latency_quirk(struct drm_i915_private *dev_priv) * The BIOS provided WM memory latency values are often * inadequate for high resolution displays. Adjust them. */ - changed = ilk_increase_wm_latency(dev_priv, dev_priv->wm.pri_latency, 12) | - ilk_increase_wm_latency(dev_priv, dev_priv->wm.spr_latency, 12) | - ilk_increase_wm_latency(dev_priv, dev_priv->wm.cur_latency, 12); + changed = ilk_increase_wm_latency(dev_priv, dev_priv->wm.pri_latency, 12); + changed |= ilk_increase_wm_latency(dev_priv, dev_priv->wm.spr_latency, 12); + changed |= ilk_increase_wm_latency(dev_priv, dev_priv->wm.cur_latency, 12);
if (!changed) return;
From: Arnd Bergmann arnd@arndb.de
stable inclusion from stable-v5.10.92 commit c0091233f3d8f4c49a76546a387a783324a6b0ec bugzilla: 186193 https://gitee.com/openeuler/kernel/issues/I53108
Reference: https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?id=...
--------------------------------
commit 144779edf598e0896302c35a0926ef0b68f17c4b upstream.
clang warns about excessive stack usage in this driver when UBSAN is enabled:
drivers/staging/greybus/audio_topology.c:977:12: error: stack frame size of 1836 bytes in function 'gbaudio_tplg_create_widget' [-Werror,-Wframe-larger-than=]
Rework this code to no longer use compound literals for initializing the structure in each case, but instead keep the common bits in a preallocated constant array and copy them as needed.
Link: https://github.com/ClangBuiltLinux/linux/issues/1535 Link: https://lore.kernel.org/r/20210103223541.2790855-1-arnd@kernel.org/ Reviewed-by: Nick Desaulniers ndesaulniers@google.com Reviewed-by: Alex Elder elder@linaro.org Signed-off-by: Arnd Bergmann arnd@arndb.de [nathan: Address review comments from v1] Signed-off-by: Nathan Chancellor nathan@kernel.org Link: https://lore.kernel.org/r/20211209195141.1165233-1-nathan@kernel.org Signed-off-by: Greg Kroah-Hartman gregkh@linuxfoundation.org Signed-off-by: Chen Jun chenjun102@huawei.com Signed-off-by: Zheng Zengkai zhengzengkai@huawei.com Acked-by: Xie XiuQi xiexiuqi@huawei.com --- drivers/staging/greybus/audio_topology.c | 92 ++++++++++++------------ 1 file changed, 45 insertions(+), 47 deletions(-)
diff --git a/drivers/staging/greybus/audio_topology.c b/drivers/staging/greybus/audio_topology.c index 662e3e8b4b63..2bb8e7b60e8d 100644 --- a/drivers/staging/greybus/audio_topology.c +++ b/drivers/staging/greybus/audio_topology.c @@ -974,6 +974,44 @@ static int gbaudio_widget_event(struct snd_soc_dapm_widget *w, return ret; }
+static const struct snd_soc_dapm_widget gbaudio_widgets[] = { + [snd_soc_dapm_spk] = SND_SOC_DAPM_SPK(NULL, gbcodec_event_spk), + [snd_soc_dapm_hp] = SND_SOC_DAPM_HP(NULL, gbcodec_event_hp), + [snd_soc_dapm_mic] = SND_SOC_DAPM_MIC(NULL, gbcodec_event_int_mic), + [snd_soc_dapm_output] = SND_SOC_DAPM_OUTPUT(NULL), + [snd_soc_dapm_input] = SND_SOC_DAPM_INPUT(NULL), + [snd_soc_dapm_switch] = SND_SOC_DAPM_SWITCH_E(NULL, SND_SOC_NOPM, + 0, 0, NULL, + gbaudio_widget_event, + SND_SOC_DAPM_PRE_PMU | + SND_SOC_DAPM_POST_PMD), + [snd_soc_dapm_pga] = SND_SOC_DAPM_PGA_E(NULL, SND_SOC_NOPM, + 0, 0, NULL, 0, + gbaudio_widget_event, + SND_SOC_DAPM_PRE_PMU | + SND_SOC_DAPM_POST_PMD), + [snd_soc_dapm_mixer] = SND_SOC_DAPM_MIXER_E(NULL, SND_SOC_NOPM, + 0, 0, NULL, 0, + gbaudio_widget_event, + SND_SOC_DAPM_PRE_PMU | + SND_SOC_DAPM_POST_PMD), + [snd_soc_dapm_mux] = SND_SOC_DAPM_MUX_E(NULL, SND_SOC_NOPM, + 0, 0, NULL, + gbaudio_widget_event, + SND_SOC_DAPM_PRE_PMU | + SND_SOC_DAPM_POST_PMD), + [snd_soc_dapm_aif_in] = SND_SOC_DAPM_AIF_IN_E(NULL, NULL, 0, + SND_SOC_NOPM, 0, 0, + gbaudio_widget_event, + SND_SOC_DAPM_PRE_PMU | + SND_SOC_DAPM_POST_PMD), + [snd_soc_dapm_aif_out] = SND_SOC_DAPM_AIF_OUT_E(NULL, NULL, 0, + SND_SOC_NOPM, 0, 0, + gbaudio_widget_event, + SND_SOC_DAPM_PRE_PMU | + SND_SOC_DAPM_POST_PMD), +}; + static int gbaudio_tplg_create_widget(struct gbaudio_module_info *module, struct snd_soc_dapm_widget *dw, struct gb_audio_widget *w, int *w_size) @@ -1052,77 +1090,37 @@ static int gbaudio_tplg_create_widget(struct gbaudio_module_info *module,
switch (w->type) { case snd_soc_dapm_spk: - *dw = (struct snd_soc_dapm_widget) - SND_SOC_DAPM_SPK(w->name, gbcodec_event_spk); + *dw = gbaudio_widgets[w->type]; module->op_devices |= GBAUDIO_DEVICE_OUT_SPEAKER; break; case snd_soc_dapm_hp: - *dw = (struct snd_soc_dapm_widget) - SND_SOC_DAPM_HP(w->name, gbcodec_event_hp); + *dw = gbaudio_widgets[w->type]; module->op_devices |= (GBAUDIO_DEVICE_OUT_WIRED_HEADSET | GBAUDIO_DEVICE_OUT_WIRED_HEADPHONE); module->ip_devices |= GBAUDIO_DEVICE_IN_WIRED_HEADSET; break; case snd_soc_dapm_mic: - *dw = (struct snd_soc_dapm_widget) - SND_SOC_DAPM_MIC(w->name, gbcodec_event_int_mic); + *dw = gbaudio_widgets[w->type]; module->ip_devices |= GBAUDIO_DEVICE_IN_BUILTIN_MIC; break; case snd_soc_dapm_output: - *dw = (struct snd_soc_dapm_widget)SND_SOC_DAPM_OUTPUT(w->name); - break; case snd_soc_dapm_input: - *dw = (struct snd_soc_dapm_widget)SND_SOC_DAPM_INPUT(w->name); - break; case snd_soc_dapm_switch: - *dw = (struct snd_soc_dapm_widget) - SND_SOC_DAPM_SWITCH_E(w->name, SND_SOC_NOPM, 0, 0, - widget_kctls, - gbaudio_widget_event, - SND_SOC_DAPM_PRE_PMU | - SND_SOC_DAPM_POST_PMD); - break; case snd_soc_dapm_pga: - *dw = (struct snd_soc_dapm_widget) - SND_SOC_DAPM_PGA_E(w->name, SND_SOC_NOPM, 0, 0, NULL, 0, - gbaudio_widget_event, - SND_SOC_DAPM_PRE_PMU | - SND_SOC_DAPM_POST_PMD); - break; case snd_soc_dapm_mixer: - *dw = (struct snd_soc_dapm_widget) - SND_SOC_DAPM_MIXER_E(w->name, SND_SOC_NOPM, 0, 0, NULL, - 0, gbaudio_widget_event, - SND_SOC_DAPM_PRE_PMU | - SND_SOC_DAPM_POST_PMD); - break; case snd_soc_dapm_mux: - *dw = (struct snd_soc_dapm_widget) - SND_SOC_DAPM_MUX_E(w->name, SND_SOC_NOPM, 0, 0, - widget_kctls, gbaudio_widget_event, - SND_SOC_DAPM_PRE_PMU | - SND_SOC_DAPM_POST_PMD); + *dw = gbaudio_widgets[w->type]; break; case snd_soc_dapm_aif_in: - *dw = (struct snd_soc_dapm_widget) - SND_SOC_DAPM_AIF_IN_E(w->name, w->sname, 0, - SND_SOC_NOPM, - 0, 0, gbaudio_widget_event, - SND_SOC_DAPM_PRE_PMU | - SND_SOC_DAPM_POST_PMD); - break; case snd_soc_dapm_aif_out: - *dw = (struct snd_soc_dapm_widget) - SND_SOC_DAPM_AIF_OUT_E(w->name, w->sname, 0, - SND_SOC_NOPM, - 0, 0, gbaudio_widget_event, - SND_SOC_DAPM_PRE_PMU | - SND_SOC_DAPM_POST_PMD); + *dw = gbaudio_widgets[w->type]; + dw->sname = w->sname; break; default: ret = -EINVAL; goto error; } + dw->name = w->name;
dev_dbg(module->dev, "%s: widget of type %d created\n", dw->name, dw->id);
-
Zheng Zengkai