On 2021/8/14 1:55, Jakub Kicinski wrote:
On Fri, 13 Aug 2021 09:45:26 +0800 Yufeng Mo wrote:
Currently, there many drivers who support CQE mode configuration, some configure it as a fixed when initialized, some provide an interface to change it by ethtool private flags. In order make it more generic, add two new 'ETHTOOL_A_COALESCE_USE_CQE_TX' and 'ETHTOOL_A_COALESCE_USE_CQE_RX' coalesce attributes, then these parameters can be accessed by ethtool netlink coalesce uAPI.
Signed-off-by: Yufeng Mo moyufeng@huawei.com Signed-off-by: Huazhong Tan tanhuazhong@huawei.com
The series LGTM. When I was asking for documentation earlier I meant a paragraph explaining the difference between the two modes. Here is an example based on my current understanding, I could very well be wrong but you see what kind of explanation I'm after? If this is more or less correct please feel free to use it and modify as you see fit.
The description in the following document is consistent with my understanding. I'll add the following paragraph and add "Signed-off-by: Jakub Kicinski kuba@kernel.org" to the patch. Thanks for your correction.
diff --git a/Documentation/networking/ethtool-netlink.rst b/Documentation/networking/ethtool-netlink.rst index c86628e6a235..fc7ac5938aac 100644 --- a/Documentation/networking/ethtool-netlink.rst +++ b/Documentation/networking/ethtool-netlink.rst @@ -939,12 +939,25 @@ Gets coalescing parameters like ``ETHTOOL_GCOALESCE`` ioctl request. ``ETHTOOL_A_COALESCE_TX_USECS_HIGH`` u32 delay (us), high Tx ``ETHTOOL_A_COALESCE_TX_MAX_FRAMES_HIGH`` u32 max packets, high Tx ``ETHTOOL_A_COALESCE_RATE_SAMPLE_INTERVAL`` u32 rate sampling interval
- ``ETHTOOL_A_COALESCE_USE_CQE_TX`` bool timer reset mode, Tx
- ``ETHTOOL_A_COALESCE_USE_CQE_RX`` bool timer reset mode, Rx =========================================== ====== =======================
Attributes are only included in reply if their value is not zero or the corresponding bit in ``ethtool_ops::supported_coalesce_params`` is set (i.e. they are declared as supported by driver).
+Timer reset mode (``ETHTOOL_A_COALESCE_USE_CQE_TX`` and +``ETHTOOL_A_COALESCE_USE_CQE_RX``) control the interaction between packet +arrival and the various time based delay parameters. By default timers are +expected to limit the max delay between any packet arrival/departure +and a corresponding interrupt. In this mode timer should be started by packet +arrival (sometimes delivery of previous interrupt) and reset when interrupt +is delivered. +Setting the appropriate attribute to 1 will enable ``CQE`` mode, where +each packet event resets the timer. In this mode timer is used to force +the interrupt if queue goes idle, while busy queues depend on the packet +limit to trigger interrupts.
COALESCE_SET
@@ -977,6 +990,8 @@ Sets coalescing parameters like ``ETHTOOL_SCOALESCE`` ioctl request. ``ETHTOOL_A_COALESCE_TX_USECS_HIGH`` u32 delay (us), high Tx ``ETHTOOL_A_COALESCE_TX_MAX_FRAMES_HIGH`` u32 max packets, high Tx ``ETHTOOL_A_COALESCE_RATE_SAMPLE_INTERVAL`` u32 rate sampling interval
- ``ETHTOOL_A_COALESCE_USE_CQE_TX`` bool timer reset mode, Tx
- ``ETHTOOL_A_COALESCE_USE_CQE_RX`` bool timer reset mode, Rx =========================================== ====== =======================
Request is rejected if it attributes declared as unsupported by driver (i.e. .