From: Lang Cheng <chenglang@huawei.com>

HIP08/09 only supports CMDQ in non-interrupt mode, and the firmware always
ignores the flag to indicate the mode. Therefore, remove the dead code.

Fixes: a04ff739f2a9 ("RDMA/hns: Add command queue support for hip08 RoCE driver")
Signed-off-by: Lang Cheng <chenglang@huawei.com>
Signed-off-by: Weihang Li <liweihang@huawei.com>
---
 drivers/infiniband/hw/hns/hns_roce_hw_v2.c | 24 ++++++++----------------
 drivers/infiniband/hw/hns/hns_roce_hw_v2.h |  2 --
 2 files changed, 8 insertions(+), 18 deletions(-)

diff --git a/drivers/infiniband/hw/hns/hns_roce_hw_v2.c b/drivers/infiniband/hw/hns/hns_roce_hw_v2.c
index 7a5a41d..260c17c 100644
--- a/drivers/infiniband/hw/hns/hns_roce_hw_v2.c
+++ b/drivers/infiniband/hw/hns/hns_roce_hw_v2.c
@@ -1197,8 +1197,7 @@ static void hns_roce_cmq_setup_basic_desc(struct hns_roce_cmq_desc *desc,
 {
 	memset((void *)desc, 0, sizeof(struct hns_roce_cmq_desc));
 	desc->opcode = cpu_to_le16(opcode);
-	desc->flag =
-		cpu_to_le16(HNS_ROCE_CMD_FLAG_NO_INTR | HNS_ROCE_CMD_FLAG_IN);
+	desc->flag = cpu_to_le16(HNS_ROCE_CMD_FLAG_IN);
 	if (is_read)
 		desc->flag |= cpu_to_le16(HNS_ROCE_CMD_FLAG_WR);
 	else
@@ -1275,18 +1274,12 @@ static int __hns_roce_cmq_send(struct hns_roce_dev *hr_dev,
 	/* Write to hardware */
 	roce_write(hr_dev, ROCEE_TX_CMQ_TAIL_REG, csq->next_to_use);
 
-	/*
-	 * If the command is sync, wait for the firmware to write back,
-	 * if multi descriptors to be sent, use the first one to check
-	 */
-	if (le16_to_cpu(desc->flag) & HNS_ROCE_CMD_FLAG_NO_INTR) {
-		do {
-			if (hns_roce_cmq_csq_done(hr_dev))
-				break;
-			udelay(1);
-			timeout++;
-		} while (timeout < priv->cmq.tx_timeout);
-	}
+	do {
+		if (hns_roce_cmq_csq_done(hr_dev))
+			break;
+		udelay(1);
+		timeout++;
+	} while (timeout < priv->cmq.tx_timeout);
 
 	if (hns_roce_cmq_csq_done(hr_dev)) {
 		handle = 0;
@@ -1626,8 +1619,7 @@ static int hns_roce_set_vf_switch_param(struct hns_roce_dev *hr_dev, int vf_id)
 	if (ret)
 		return ret;
 
-	desc.flag =
-		cpu_to_le16(HNS_ROCE_CMD_FLAG_NO_INTR | HNS_ROCE_CMD_FLAG_IN);