From: Lang Cheng chenglang@huawei.com

When reloading driver, the head/tail pointer of CMDQ may be not at position 0. Then during initialization of CMDQ, if head is reset first, the firmware will start to handle CMDQ because the head is not equal to the tail. The driver can reset tail first since the firmware will be triggerred only by head. This bug is introduced by changing macros of head/tail register without changing the order of initialization.

Besides, the same name represents opposite meanings in new/old driver, it is hard to maintain, so rename them to PI/CI.

Fixes: 292b3352bd5b ("RDMA/hns: Adjust fields and variables about CMDQ tail/head") Signed-off-by: Lang Cheng chenglang@huawei.com Signed-off-by: Weihang Li liweihang@huawei.com --- drivers/infiniband/hw/hns/hns_roce_common.h | 4 ++-- drivers/infiniband/hw/hns/hns_roce_hw_v2.c | 12 +++++++----- 2 files changed, 9 insertions(+), 7 deletions(-)

diff --git a/drivers/infiniband/hw/hns/hns_roce_common.h b/drivers/infiniband/hw/hns/hns_roce_common.h index 23c438c..8a18aa1 100644 --- a/drivers/infiniband/hw/hns/hns_roce_common.h +++ b/drivers/infiniband/hw/hns/hns_roce_common.h @@ -364,8 +364,8 @@ #define ROCEE_TX_CMQ_BASEADDR_L_REG 0x07000 #define ROCEE_TX_CMQ_BASEADDR_H_REG 0x07004 #define ROCEE_TX_CMQ_DEPTH_REG 0x07008 -#define ROCEE_TX_CMQ_HEAD_REG 0x07010 -#define ROCEE_TX_CMQ_TAIL_REG 0x07014 +#define ROCEE_TX_CMQ_PI_REG 0x07010 +#define ROCEE_TX_CMQ_CI_REG 0x07014

#define ROCEE_RX_CMQ_BASEADDR_L_REG 0x07018 #define ROCEE_RX_CMQ_BASEADDR_H_REG 0x0701c diff --git a/drivers/infiniband/hw/hns/hns_roce_hw_v2.c b/drivers/infiniband/hw/hns/hns_roce_hw_v2.c index c3934ab..c359f09 100644 --- a/drivers/infiniband/hw/hns/hns_roce_hw_v2.c +++ b/drivers/infiniband/hw/hns/hns_roce_hw_v2.c @@ -1194,8 +1194,10 @@ static void hns_roce_cmq_init_regs(struct hns_roce_dev *hr_dev, bool ring_type) upper_32_bits(dma)); roce_write(hr_dev, ROCEE_TX_CMQ_DEPTH_REG, (u32)ring->desc_num >> HNS_ROCE_CMQ_DESC_NUM_S); - roce_write(hr_dev, ROCEE_TX_CMQ_HEAD_REG, 0); - roce_write(hr_dev, ROCEE_TX_CMQ_TAIL_REG, 0); + + /* Make sure to write CI first and then PI */ + roce_write(hr_dev, ROCEE_TX_CMQ_CI_REG, 0); + roce_write(hr_dev, ROCEE_TX_CMQ_PI_REG, 0); } else { roce_write(hr_dev, ROCEE_RX_CMQ_BASEADDR_L_REG, (u32)dma); roce_write(hr_dev, ROCEE_RX_CMQ_BASEADDR_H_REG, @@ -1275,7 +1277,7 @@ static void hns_roce_cmq_setup_basic_desc(struct hns_roce_cmq_desc *desc,

static int hns_roce_cmq_csq_done(struct hns_roce_dev *hr_dev) { - u32 tail = roce_read(hr_dev, ROCEE_TX_CMQ_TAIL_REG); + u32 tail = roce_read(hr_dev, ROCEE_TX_CMQ_CI_REG); struct hns_roce_v2_priv *priv = hr_dev->priv;

return tail == priv->cmq.csq.head; @@ -1303,7 +1305,7 @@ static int __hns_roce_cmq_send(struct hns_roce_dev *hr_dev, }

/* Write to hardware */ - roce_write(hr_dev, ROCEE_TX_CMQ_HEAD_REG, csq->head); + roce_write(hr_dev, ROCEE_TX_CMQ_PI_REG, csq->head);

/* If the command is sync, wait for the firmware to write back, * if multi descriptors to be sent, use the first one to check @@ -1334,7 +1336,7 @@ static int __hns_roce_cmq_send(struct hns_roce_dev *hr_dev, } } else { /* FW/HW reset or incorrect number of desc */ - tail = roce_read(hr_dev, ROCEE_TX_CMQ_TAIL_REG); + tail = roce_read(hr_dev, ROCEE_TX_CMQ_CI_REG); dev_warn(hr_dev->dev, "CMDQ move tail from %d to %d\n", csq->head, tail); csq->head = tail;