hulk inclusion category: bugfix bugzilla: https://atomgit.com/openeuler/kernel/issues/9343 -------------------------------- The ARM64 FEAT_NMI implementation relies on two independent hardware validation paths: 1. CPU Feature Check (`system_uses_nmi()`): Validates if the PE supports FEAT_NMI via ID_AA64PFR1_EL1.NMI. If pseudo-NMI is disabled and this bit is set, enables SCTLR_EL1.NMI (map to SCTLR_EL2.NMI in VHE mode) and clears SCTLR_EL1.SPINTMASK. Once active, the hardware automatically sets PSTATE.ALLINT upon taking an exception to EL1/EL2, effectively masking interrupts. `sysreg_clear_set(sctlr_el1, SCTLR_EL1_SPINTMASK, SCTLR_EL1_NMI)` 2. GICv3 Feature Check (gic_data.has_nmi): Validates if the interrupt controller supports Non-maskable Interrupts via GICD_TYPER.NMI. `gic_data.has_nmi = !!(typer & GICD_TYPER_NMI)` And PSTATE.ALLINT is strictly a PE-level state register. Its existence and behavior are entirely independent of whether the underlying GICv3 hardware implementation has its own FEAT_NMI capabilities enabled. Currently, __gic_handle_irq_from_irqson() uses has_v3_3_nmi() to guard the clearing of PSTATE.ALLINT. This creates a destructive dependency where the GIC's NMI status dictates PE register management. static inline bool has_v3_3_nmi(void) { return gic_data.has_nmi && system_uses_nmi(); } If a platform features a PE that supports FEAT_NMI but has a GICv3 that does not support (or has disabled) the NMI feature, the current implementation fails to clear ALLINT during IRQ handling. Because ALLINT is automatically set by the hardware exception entry, it remains permanently set. As a consequence, local_irq_enable() only clears PSTATE.I and F bits, leaving ALLINT untouched. Since ALLINT masks both standard IRQs and NMIs, even if PSTATE.I cleared, the system becomes completely incapable of responding to subsequent NMIs and standard IRQs during downstream processing (such as softirq execution). handle_softirqs() -> local_irq_enable() -> asm volatile("msr daifclr, #3") -> do pending softirq action -> local_irq_disable() -> asm volatile("msr daifset, #3") Fix this by replacing the has_v3_3_nmi() check with system_uses_nmi() when clearing ALLINT. This ensures that PE state management correctly reflects PE capabilities. Additionally, explicitly log whether the GIC supports hardware NMI based on the GICD_TYPER.NMI bit during initialization. Since FEAT_NMI deployment relies on both subsystems, printing this status provides critical diagnostic information for system verification. Fixes: eefea6156921 ("irqchip/gic-v3: Fix hard LOCKUP caused by NMI being masked") Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com> --- drivers/irqchip/irq-gic-v3.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) diff --git a/drivers/irqchip/irq-gic-v3.c b/drivers/irqchip/irq-gic-v3.c index eba578a32d2d..77ffded0ff81 100644 --- a/drivers/irqchip/irq-gic-v3.c +++ b/drivers/irqchip/irq-gic-v3.c @@ -1040,7 +1040,7 @@ asmlinkage void __exception_irq_entry gic_handle_irq_noack(struct pt_regs *regs) if (gic_prio_masking_enabled()) { gic_pmr_mask_irqs(); gic_arch_enable_irqs(); - } else if (has_v3_3_nmi()) { + } else if (system_uses_nmi()) { #ifdef CONFIG_ARM64_NMI _allint_clear(); #endif @@ -2479,6 +2479,7 @@ static int __init gic_init_bases(phys_addr_t dist_phys_base, gic_data.has_rss = !!(typer & GICD_TYPER_RSS); gic_data.has_nmi = !!(typer & GICD_TYPER_NMI); + pr_info("GICD_TYPER NMI is%s supported.\n", gic_data.has_nmi ? "" : " not"); if (typer & GICD_TYPER_MBIS) { err = mbi_init(handle, gic_data.domain); -- 2.34.1