From: Peng Li lipeng321@huawei.com

Remove repeated words "to" and "try".

Signed-off-by: Peng Li lipeng321@huawei.com Signed-off-by: Huazhong Tan tanhuazhong@huawei.com --- drivers/net/ethernet/intel/i40e/i40e_main.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/drivers/net/ethernet/intel/i40e/i40e_main.c b/drivers/net/ethernet/intel/i40e/i40e_main.c index 0f84ed0..1555d60 100644 --- a/drivers/net/ethernet/intel/i40e/i40e_main.c +++ b/drivers/net/ethernet/intel/i40e/i40e_main.c @@ -7339,7 +7339,7 @@ static void i40e_vsi_set_default_tc_config(struct i40e_vsi *vsi) qcount = min_t(int, vsi->alloc_queue_pairs, i40e_pf_get_max_q_per_tc(vsi->back)); for (i = 0; i < I40E_MAX_TRAFFIC_CLASS; i++) { - /* For the TC that is not enabled set the offset to to default + /* For the TC that is not enabled set the offset to default * queue and allocate one queue for the given TC. */ vsi->tc_config.tc_info[i].qoffset = 0; @@ -10625,7 +10625,7 @@ static void i40e_rebuild(struct i40e_pf *pf, bool reinit, bool lock_acquired) * need to rebuild the switch model in the HW. * * If there were VEBs but the reconstitution failed, we'll try - * try to recover minimal use by getting the basic PF VSI working. + * to recover minimal use by getting the basic PF VSI working. */ if (vsi->uplink_seid != pf->mac_seid) { dev_dbg(&pf->pdev->dev, "attempting to rebuild switch\n");

From: Peng Li lipeng321@huawei.com

Remove repeated word "to".

Signed-off-by: Peng Li lipeng321@huawei.com Signed-off-by: Huazhong Tan tanhuazhong@huawei.com --- drivers/net/phy/mdio_bus.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/net/phy/mdio_bus.c b/drivers/net/phy/mdio_bus.c index 8235185..dadf75f 100644 --- a/drivers/net/phy/mdio_bus.c +++ b/drivers/net/phy/mdio_bus.c @@ -510,7 +510,7 @@ static int mdiobus_create_device(struct mii_bus *bus, * on a given bus, and attach them to the bus. Drivers should use * mdiobus_register() rather than __mdiobus_register() unless they * need to pass a specific owner module. MDIO devices which are not - * PHYs will not be brought up by this function. They are expected to + * PHYs will not be brought up by this function. They are expected * to be explicitly listed in DT and instantiated by of_mdiobus_register(). * * Returns 0 on success or < 0 on error.

On 3/30/21 2:27 AM, Huazhong Tan wrote:

From: Peng Li lipeng321@huawei.com

Remove repeated words "that" and "the".

Signed-off-by: Peng Li lipeng321@huawei.com Signed-off-by: Huazhong Tan tanhuazhong@huawei.com

Acked-by: Alex Elder elder@linaro.org

---

drivers/net/ipa/ipa_endpoint.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/drivers/net/ipa/ipa_endpoint.c b/drivers/net/ipa/ipa_endpoint.c index 38e83cd..dd24179 100644 --- a/drivers/net/ipa/ipa_endpoint.c +++ b/drivers/net/ipa/ipa_endpoint.c @@ -809,7 +809,7 @@ static u32 hol_block_timer_val(struct ipa *ipa, u32 microseconds) * The best precision is achieved when the base value is as * large as possible. Find the highest set bit in the tick * count, and extract the number of bits in the base field

• * such that that high bit is included.
  

• * such that high bit is included.
  

  */ high = fls(ticks); /* 1..32 */ width = HWEIGHT32(BASE_VALUE_FMASK);

@@ -1448,7 +1448,7 @@ static int ipa_endpoint_reset_rx_aggr(struct ipa_endpoint *endpoint) if (ret) goto out_suspend_again;

• /* Finally, reset and reconfigure the channel again (re-enabling the

• /* Finally, reset and reconfigure the channel again (re-enabling
  • the doorbell engine if appropriate). Sleep for 1 millisecond to
  • complete the channel reset sequence. Finish by suspending the
  • channel again (if necessary).

Huazhong Tan tanhuazhong@huawei.com wrote:

From: Peng Li lipeng321@huawei.com

Remove repeated word "that".

Signed-off-by: Peng Li lipeng321@huawei.com Signed-off-by: Huazhong Tan tanhuazhong@huawei.com

---

drivers/net/bonding/bond_alb.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/net/bonding/bond_alb.c b/drivers/net/bonding/bond_alb.c index c3091e0..3455f2c 100644 --- a/drivers/net/bonding/bond_alb.c +++ b/drivers/net/bonding/bond_alb.c @@ -1098,7 +1098,7 @@ static void alb_fasten_mac_swap(struct bonding *bond, struct slave *slave1,

• If @slave's permanent hw address is different both from its current
• address and from @bond's address, then somewhere in the bond there's
• a slave that has @slave's permanet address as its current address.

• • We'll make sure that that slave no longer uses @slave's permanent address.

• • We'll make sure that slave no longer uses @slave's permanent address.

This is actually correct as written, but I can see that it's a bit confusing. Rather than removing the second that, I'd suggest changing it to "... make sure the other slave no longer uses ..." to be clearer.

-J

--- -Jay Vosburgh, jay.vosburgh@canonical.com